Re: syncrange listing?

[Mihai Amariutei <mihai@ambra.ro>]

Sync = 127 very good signal (low BER)
Sync = 95 lower signal quality, still working
Sync = 63 low signal quality, margimally working (High BER)
Under 31 : low signal, syncronisation impossible.

0 means no signall at all.

Mihai

----- Original Message -----
From: "Robin Edgar Tripany" <red@tripany.com>
To: "Uwe Guenther" <uwe@cscc.de>; <linux-dvb@linuxtv.org>
Sent: Monday, October 23, 2000 3:54 PM
Subject: syncrange listing?


> I'm now getting this for a sync... does anyone have a list of sync numbers
> and their meanings?
>
> Fsync = 0, Freq = 2033000000, Sync = 0 Afc = 4292904796 Agc = 159 Nest =
> 49152 Vber = 165672
>
> cheers,
> Robin
> ----- Original Message -----
> From: "Uwe Guenther" <uwe@cscc.de>
> To: "Robin Edgar Tripany" <red@tripany.com>
> Sent: Friday, October 13, 2000 1:33 AM
> Subject: Re: Routing Probs with dvb0
>
>
> > Robin Edgar Tripany wrote:
> > >
> > > K...... got dvbd drivers compiled, installed and they work :)
> > >
> > > got dvbd compiled and dvbd.conf editted to my specific settings....
> > > my primary questions are:
> > >
> > > 1. When i run dvbd without the -q option i get these lines over and
over
> > > again:
> > >
> > >     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc =
319
> Nest
> > > = 43264"
> > >     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc =
303
> Nest
> > > = 43776"
> > sync=3 means bad signal
> >
> > you should get sync=127
> >
> > >
> > >     is this ok?
> > > 2. How many filters do i need in /etc/dvbd.conf?
> > >     (under windows i have 5!!!!)
> > i have 2
> > > 3. how do you set a MAC address on your card?
> > > 4. as i understand you have to use mrouted to multicast your streams,
> > >     what are the tunnel settings? (local ip = my uplink device?
> remote=???)
> > >     might you have your mrouted.conf file?
> > >      I dont really understand the mrouted.conf file :)))
> > >
> > >     "phyint dvb0 altnet 212.17.1.212/1 altnet 125.0.0.0/1"
> > >     "phyint eth0"
> > >
> > >     is the first altnet my ppp device and the second one the
destination
> > > address?
> >  I don`t use mrouted
> >
> > I don´t understand this stuff too :))
> >
> > >
> > > well, i hope someone can help me :)
> > >
> > > thanx
> > >
> > > robin
> > >
> > > ----- Original Message -----
> > > From: "Uwe Guenther" <uwe@cscc.de>
> > > To: "Robin Edgar Tripany" <red@tripany.com>
> > > Sent: Thursday, October 05, 2000 5:28 PM
> > > Subject: Re: Routing Probs with dvb0
> > >
> > > > Robin Edgar Tripany wrote:
> > > > >
> > > > > What did you use to get EON working?! where can i find the
sources?
> > > > >
> > > >
> > > > http://www.linuxtv.org/download/dvb/siemens_dvb-0.7.1.tar.gz
> > > > http://www.linuxtv.org/download/dvb/dvbd2.tar.gz
> > > >
> > > >  and you could check my config, they is located at
> > > >
> > > > http://www.cscc.de/eon.tar.gz
> > > >
> > > >
> > > > ... may the Tux be with you! =Uwe=
> > > > --
> > > > Uwe Günther                    \\://
> mailto:uwe@cscc.de
> > > > Haupstraße 88                  (o -)
> http://www.cscc.de
> > > > 98631 Behrungen          ---ooO-(_)-Ooo---
> tel.:+49.36944.54448
> > > > Germany                                       Linux, enjoy the ride
> ...!
> > > >
> >
> > --
> > ... may the Tux be with you! =Uwe=
> > --
> > Uwe Günther                    \\://                  mailto:uwe@cscc.de
> > Haupstraße 88                  (o -)                  http://www.cscc.de
> > 98631 Behrungen          ---ooO-(_)-Ooo---          tel.:+49.36944.54448
> > Germany                                       Linux, enjoy the ride ...!
> >
>
>