Mailing List archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[linux-dvb] Re: need help with linux dvb driver
Hi
first Thanks for replying me fastly.
in fact, i try everythings just to get this card
working, after i insmod the "dst" and fail to get the
VDR or xawtv to work with, i tried to insmod the
"CX24110" to see if it works, but nothings happen, the
i tried remove the "dst" and insmod it again with
"DST_TYPE_FLAGS=0",
"DST_TYPE_FLAGS=1","DST_TYPE_FLAGS=4", but again
nothings happen and the VDR cannot crab the
/dev/video0 devices.
now, i am trying again form the begining, so please
follow my steps and correct me if i am wrong
1) "lsmod" gives
******************************
[abbas@localhost abbas]$ lsmod
Module Size Used by
autofs 17152 0
parport_pc 36492 2
2) i did the following step
*******************************
[root@localhost abbas]# modprobe bttv card=0x68
i2c_hw=1
[root@localhost abbas]# lsmod
Module Size Used by
bttv 136096 0
video_buf 22272 1 bttv
i2c_algo_bit 10504 1 bttv
btcx_risc 4996 1 bttv
i2c_core 25348 2 bttv,i2c_algo_bit
autofs 17152 0
parport_pc 36492 2
3) modprobe dvb-bt8xx
**************************
[root@localhost abbas]# modprobe dvb-bt8xx
[root@localhost abbas]# lsmod
Module Size Used by
dvb_bt8xx 8064 0
dvb_core 60544 1 dvb_bt8xx
bt878 11696 1 dvb_bt8xx
bttv 136096 2 dvb_bt8xx,bt878
video_buf 22272 1 bttv
i2c_algo_bit 10504 1 bttv
btcx_risc 4996 1 bttv
i2c_core 25348 3
dvb_bt8xx,bttv,i2c_algo_bit
autofs 17152 0
parport_pc 36492 2
4)modprobe dst
******************************
[root@localhost abbas]# lsmod
Module Size Used by
dst 14464 0
dvb_bt8xx 8064 0
dvb_core 60544 2 dst,dvb_bt8xx
bt878 11696 2 dst,dvb_bt8xx
bttv 136096 2 dvb_bt8xx,bt878
video_buf 22272 1 bttv
i2c_algo_bit 10504 1 bttv
btcx_risc 4996 1 bttv
i2c_core 25348 3
dvb_bt8xx,bttv,i2c_algo_bit
autofs 17152 0
parport_pc 36492 2
5) dmesg "part of it"
*************************
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
es1371: version v0.32 time 20:01:39 Dec 20 2003
PCI: Found IRQ 3 for device 0000:02:0a.0
es1371: found chip, vendor id 0x1274 device id 0x5880
revision 0x02
es1371: found es1371 rev 2 at io 0xdf00 irq 3 joystick
0x0
ac97_codec: AC97 Audio codec, id: 0x8384:0x7609
(SigmaTel STAC9721/23)
btaudio: driver version 0.7 loaded [digital+analog]
PCI: Found IRQ 11 for device 0000:02:0d.1
PCI: Sharing IRQ 11 with 0000:02:0d.0
btaudio: Bt878 (rev 17) at 02:0d.1, irq: 11, latency:
32, mmio: 0xf47ff000
btaudio: using card config "default"
btaudio: registered device dsp2 [digital]
btaudio: registered device dsp3 [analog]
btaudio: registered device mixer1
Advanced Linux Sound Architecture Driver Version 0.9.7
(Thu Sep 25 19:16:36 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0.
error = -16
unable to register OSS PCM device 0:0
unable to register OSS mixer device 0:0
unable to register OSS mixer device 1:0
ALSA device list:
#0: Dummy 1
#1: Virtual MIDI Card 1
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind
65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
IrCOMM protocol (Dag Brattli)
EXT3-fs: INFO: recovery required on readonly
filesystem.
EXT3-fs: write access will be enabled during recovery.
hub 1-0:1.0: new USB device on port 1, assigned
address 2
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 188k freed
input: USB HID v1.00 Mouse [Cypress Sem Cypress USB
Mouse] on usb-0000:00:1f.2-1
hub 1-0:1.0: new USB device on port 2, assigned
address 3
drivers/usb/class/usblp.c: usblp0: USB Bidirectional
printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7004
EXT3 FS on hda9, internal journal
Adding 232900k swap on /dev/hda7. Priority:-1
extents:1
cdrom: open failed.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kudzu: numerical sysctl 1 23 is obsolete.
parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP]
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
plip: parport0 has no IRQ. Using IRQ-less mode,which
is fairly inefficient!
NET3 PLIP version 2.4-parport gniibe@mri.co.jp
plip0: Parallel port at 0x378, not using IRQ.
lp0: using parport0 (polling).
eth0: Setting full-duplex based on MII #1 link partner
capability of 45e1.
spurious 8259A interrupt: IRQ7.
bttv: driver version 0.9.12 loaded
bttv: using 8 buffers with 2080k (520 pages) each for
capture
bttv: Bt8xx card found (0).
PCI: Found IRQ 11 for device 0000:02:0d.0
PCI: Sharing IRQ 11 with 0000:02:0d.1
bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 11,
latency: 32, mmio: 0xf47fe000
bttv0: using: Nebula Electronics DigiTV
[card=104,insmod option]
bttv0: using tuner=-1
bt878: AUDIO driver version 0.0.0 loaded
dvb_bt8xx: unable to determine DMA core of card 0
attach: checking "bt878 #0 [hw]"
find by pci: checking "bt878 #0 [hw]"
5) trying to run "vdr"
***********************
[root@localhost abbas]# vdr
vdr: no primary device found - using first device!
6) running xawtv
**********************
[root@localhost abbas]# xawtv
This is xawtv-3.90, running on Linux/i686
(2.6.0-test11)
can't open /dev/video0: No such device
v4l-conf had some trouble, trying to continue anyway
v4l2: open /dev/video0: No such device
v4l2: open /dev/video0: No such device
v4l: open /dev/video0: No such device
no video grabber device available
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&
Please correct me if there is any wrong in the
previous steps. tell me if there is any chance to get
this card working under Linux
Thanks &
best regards
abbas almutawa
--- Manu Abraham <manu@kromtek.com> wrote:
> Hi,
> The card is a Pinnacle card or is the CX24110
> module loaded as it is by some
> script ?
>
> Maybe the modules are confused looking for a
> Pinnacle PC TV@ SAT card(CX24110
> chipset) ? The removal of the module and loading the
> modules proper with the
> DST_TYPE_FLAGS would help ?
>
>
> Regards,
> Manu
>
> On Sunday 21 December 2003 23:10, ABBAS AL-MUTAWA
> wrote:
> > Dear Sir
> >
> > I have DVB card, "TWINHAN VP1020" built on bt878.
> i've
> > just correctly installed the latest DVB driver on
> > kernel-2.6.0-test11. everythings seems to work
> very
> > well, I insmod the driver as wriiten in the
> DVB-kernel
> > without any errors.
> >
> > now, i have just installed DVB player which is the
> > VDR, but when i try to run "vdr", i get the
> following
> > message.
> >
> > vdr: no primary device found - using first device!
> >
> >
> > the "lsmod" command gives
> >
__________________________________
Do you Yahoo!?
New Yahoo! Photos - easier uploading and sharing.
http://photos.yahoo.com/
--
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.
Home |
Main Index |
Thread Index