[linux-dvb] No firmware upload? WinTV Nova-T

Q raid517 at fairadsl.co.uk
Sat Apr 9 05:58:34 CEST 2005


Hi I know this is an old problem. But can someone tell me why I can't 
get my firmware to upload for my WinTV Nova-t TV card?

I have tried using the version that came with my TV card - although it 
is quite old. I tried using the version mentioned in the old kernel docs 
for 2.6.8 (which is the last time I had it working). I correctly renamed 
the file to tda1004x.bin, I have (as far as I can tell) all the required 
devices in /dev/dvb - so the only thing preventing me from getting up 
and running is to somehow get my firmware to upload. What firmware do I 
need for the 2.6.11x kernels and where can I obtain this?

Just in case anyone asks, here is the output of ls mod and dmesg:

Any input anyone can offer at all would be very much appreciated.

Module                  Size  Used by
pcmcia                 25992  0
yenta_socket           23176  0
rsrc_nonstatic         11008  1 yenta_socket
pcmcia_core            50740  3 pcmcia,yenta_socket,rsrc_nonstatic
lp                     11716  0
battery                10244  0
container               4608  0
8250_pnp                8704  0
8250_pci               18560  0
8250                   34340  2 8250_pnp,8250_pci
serial_core            23808  1 8250
ipt_LOG                 7680  1
ipt_limit               2816  4
ipt_state               2048  1
ip_conntrack_ftp       73360  0
ip_conntrack           45592  2 ipt_state,ip_conntrack_ftp
iptable_filter          3200  1
ip_tables              23296  4 ipt_LOG,ipt_limit,ipt_state,iptable_filter
floppy                 59600  0
snd_emu10k1           103172  2
snd_ac97_codec         77560  1 snd_emu10k1
snd_pcm_oss            53792  0
snd_mixer_oss          20480  1 snd_pcm_oss
snd_pcm                95880  4 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_seq_oss            35840  0
snd_seq_midi            8992  0
snd_seq_midi_event      8320  2 snd_seq_oss,snd_seq_midi
snd_seq                55952  5 snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ntfs                  187792  0
ide_generic             1408  0 [permanent]
aec62xx                 7808  0 [permanent]
trm290                  4484  0 [permanent]
alim15x3               10892  0 [permanent]
hpt34x                  5376  0 [permanent]
hpt366                 20096  0 [permanent]
cmd64x                 12188  0 [permanent]
piix                   10756  0 [permanent]
rz1000                  2688  0 [permanent]
slc90e66                6016  0 [permanent]
cs5530                  5120  0 [permanent]
sc1200                  7424  0 [permanent]
triflex                 3840  0 [permanent]
atiixp                  6544  0 [permanent]
pdc202xx_new            9344  0 [permanent]
opti621                 4868  0 [permanent]
ns87415                 3912  0 [permanent]
cy82c693                4736  0 [permanent]
serverworks             7816  0 [permanent]
amd64_agp              12744  1
agpgart                35240  1 amd64_agp
sata_nv                 9476  0
libata                 48644  1 sata_nv
ohci1394               35844  0
sbp2                   25096  0
ieee1394              112184  2 ohci1394,sbp2
sd_mod                 16528  0
usb_storage            65312  0
psmouse                29832  0
evdev                   9728  0
ide_cd                 42116  0
tsdev                   7872  0
sr_mod                 18852  0
cdrom                  41376  2 ide_cd,sr_mod
vfat                   14464  0
fat                    41628  1 vfat
loop                   17160  0
snd_rawmidi            25888  2 snd_emu10k1,snd_seq_midi
snd_seq_device          8972  5 
snd_emu10k1,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd_timer              26500  3 snd_emu10k1,snd_pcm,snd_seq
snd_page_alloc         10116  2 snd_emu10k1,snd_pcm
snd_util_mem            4736  1 snd_emu10k1
snd_hwdep              10016  1 snd_emu10k1
snd                    58468  14 
snd_emu10k1,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_seq,snd_rawmidi,snd_seq_device,snd_timer,snd_hwdep
i2c_nforce2             6784  0
ohci_hcd               22152  0
ehci_hcd               35208  0
usbcore               122488  4 usb_storage,ohci_hcd,ehci_hcd
forcedeth              19584  0
shpchp                101476  0
pci_hotplug            12932  1 shpchp
budget_ci              14080  0
tda1004x               14980  1 budget_ci
firmware_class         10880  1 budget_ci
budget_core            10244  1 budget_ci
dvb_core               86696  2 budget_ci,budget_core
saa7146                19108  2 budget_ci,budget_core
ttpci_eeprom            2944  1 budget_core
stv0299                10756  1 budget_ci
i2c_core               23312  6 
i2c_nforce2,budget_ci,tda1004x,budget_core,ttpci_eeprom,stv0299
emu10k1_gp              3840  0
gameport                4992  1 emu10k1_gp
rtc                    13496  0
pcspkr                  3940  0
parport_pc             41796  1
parport                38216  2 lp,parport_pc
ipv6                  262400  8
ac                      4996  0
thermal                13576  0
processor              23220  1 thermal
button                  6800  0
fan                     4612  0
video                  16260  0
raid517 at Linux1:~$ dmesg
eing initrd memory: 4884k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbe50, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, 
disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas at hp.com
** so I can fix the driver.
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
audit: initializing netlink socket (disabled)
audit(1113020833.464:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
devfs: boot_options: 0x1
Initializing Cryptographic API
vesafb: framebuffer at 0xd8000000, mapped to 0xe0880000, using 1200k, 
total 16384k
vesafb: mode is 640x480x16, linelength=1280, pages=24
vesafb: protected mode interface info at c000:ab90
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 80x30
fb0: VESA VGA frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
spurious 8259A interrupt: IRQ7.
ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
ACPI: PS/2 Mouse Controller [PS2M] at irq 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 5 (level, low) -> IRQ 5
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xe0802000, 00:11:09:c7:24:91, IRQ 5
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6B200P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY DVD-ROM DDU1612, ATAPI CD/DVD-ROM drive
hdd: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63, 
UDMA(133)
hda: cache flushes supported
 /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 32768 (order: 6, 262144 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
PM: Reading swsusp image.
PM: Resume from disk failed.
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4884KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Mounted devfs on /dev
Mounted devfs on /dev
Freeing unused kernel memory: 180k freed
ACPI: Power Button (FF) [PWRF]
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
input: PC Speaker
Real Time Clock Driver v1.12
gameport: pci0000:02:07.1 speed 1193 kHz
saa7146: register extension 'budget_ci dvb'.
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 11 (level, low) -> IRQ 11
saa7146: found saa7146 @ mem e09e4000 (revision 1, irq 11) (0x13c2,0x1011).
DVB: registering new adapter (TT-Budget/WinTV-NOVA-T  PCI).
adapter has MAC addr = 00:d0:5c:22:0b:bf
DVB: registering frontend 0 (Philips TDA10045H DVB-T)...
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.31.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI interrupt 0000:00:05.0[A] -> GSI 3 (level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:05.0 to 64
eth1: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:02.2: PCI device 10de:00e8 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 11, pci mem 0xf5003000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.0: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 11, pci mem 0xf5001000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:02.1: PCI device 10de:00e7 (nVidia Corporation)
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 11, pci mem 0xf5002000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-2: nForce2 SMBus adapter at 0x4c40
snd_ac97_codec: Unknown symbol snd_interval_refine
snd_ac97_codec: Unknown symbol snd_pcm_hw_rule_add
loop: loaded (max 8 devices)
ts: Compaq touchscreen protocol output
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ohci_hcd 0000:00:02.0: wakeup
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
usb 2-3: new full speed USB device using ohci_hcd and address 2
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ieee1394: Initialized config rom entry `ip1394'
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
sbp2: $Rev: 1219 $ Ben Collins <bcollins at debian.org>
ohci1394: $Rev: 1223 $ Ben Collins <bcollins at debian.org>
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 3
ACPI: PCI interrupt 0000:02:07.2[B] -> GSI 3 (level, low) -> IRQ 3
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[3]  
MMIO=[f3007000-f30077ff]  Max Packet=[2048]
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 5
ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 5 (level, low) -> IRQ 5
ohci1394: fw-host1: OHCI-1394 1.0 (PCI): IRQ=[5]  
MMIO=[f3005000-f30057ff]  Max Packet=[2048]
libata version 1.10 loaded.
sata_nv version 0.6
ACPI: PCI Interrupt Link [LSID] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC000 irq 11
ata2: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC008 irq 11
ata1: no device found (phy stat 00000000)
scsi1 : sata_nv
ata2: no device found (phy stat 00000000)
scsi2 : sata_nv
ACPI: PCI Interrupt Link [LFID] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 10
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 10
ata3: no device found (phy stat 00000000)
scsi3 : sata_nv
ata4: no device found (phy stat 00000000)
scsi4 : sata_nv
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xe8000000
Probing IDE interface ide2...
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c01010072f5]
ieee1394: Host added: ID:BUS[1-00:1023]  GUID[0010dc0000685f71]
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
  Vendor: USB 2.0   Model: Storage Device    Rev: 0100
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
ReiserFS: hda5: found reiserfs format "3.6" with standard journal
ReiserFS: hda5: using ordered data mode
ReiserFS: hda5: journal params: device hda5, size 8192, journal first 
block 18, max trans len 1024, max batch 900, max commit age 30, max 
trans age 30
ReiserFS: hda5: checking transaction log (hda5)
ReiserFS: hda5: Using r5 hash to sort names
NTFS driver 2.1.22 [Flags: R/W MODULE].
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 10 (level, low) -> IRQ 10
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
cdrom: open failed.
Adding 1049592k swap on /boot/linux-swap.swp.  Priority:-1 extents:215
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 216 bytes per conntrack
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
r8169: eth0: link up
eth0: no IPv6 routers present
ibm_acpi: ec object not found
lp0: using parport0 (interrupt-driven).
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
tda1004x: waiting for firmware upload...
tda1004x: no firmware upload (timeout or file not found?)
tda1004x: firmware upload failed
tda1004x: waiting for firmware upload...
tda1004x: no firmware upload (timeout or file not found?)
tda1004x: firmware upload failed
raid517 at Linux1:~$







More information about the linux-dvb mailing list