[linux-dvb] Twinhan Cab-CI 2031

Raido raidoz at hot.ee
Wed Dec 14 10:22:10 CET 2005


After some searching I actualy figured out where the change had to be 
made, but still no luck. Now from dmesg:
    dst_get_device_id: Recognise [DCT-CI]
    DST type flags : 0x1 newtuner 0x10 firmware version = 2

Unfortunately scan still gives me:
    scan -v est > channels.conf
    scanning est
    using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
    initial transponder 322000000 6875000 0 5
    >>> tune to: 322000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_256
    >>> tuning status == 0x00
    ...
    >>> tuning status == 0x00
    WARNING: >>> tuning failed!!!
    >>> tune to: 322000000:INVERSION_AUTO:6875000:FEC_NONE:QAM_256 
(tuning failed)
    >>> tuning status == 0x00
    ...
    >>> tuning status == 0x00
    WARNING: >>> tuning failed!!!
    ERROR: initial tuning failed
    dumping lists (0 services)
    Done.

Perhaps someone could send me a working version of drivers?



Per Dalén wrote:

> Hi,
>
> I have the same card as You and I had also problems with 
> tuning/scaning berfore I changed the dst_tlist[] to be
> ".type_flags = DST_TYPE_HAS_NEWTUNE | DST_TYPE_HAS_FW_2" as Manu 
> suggested.
> I have not tested the new combined v4l/dvb cvs yet (hope that I will 
> find som time for that during the weekend).
> So try to change and see if it makes any difference.
>
> regards
> Per Dalén
>
> Raido wrote:
>
>>  >From what I can tell, they already have a channels.conf, but I am 
>> unable to create one.
>>
>> Svein Olav Bjerkeset wrote:
>>
>>> Hi,
>>>
>>> Check this link from the mailing list archive:
>>>
>>> http://www.linuxtv.org/pipermail/linux-dvb/2005-September/004866.html
>>>
>>> Svein Olav Bjerkeset
>>>
>>>  
>>>
>>>> Hi,
>>>>
>>>> I have a Twinhan Cab-CI card and I've been trying to get it to work in
>>>> my Debian machine, I want to use it as a MythTV backend eventually. 
>>>> The
>>>> card is a model 20310(says so on the box). At first I tried it with 
>>>> the
>>>> drivers that came with 2.6.14.1, but all I got  from scan was ">>>
>>>> tuning status == 0x00". So I tried the more-or-less latest CVS and a
>>>> snapshot, but the only difference was that the scanning got faster(it
>>>> was very slow at first). Right now I compiled a 2.6.14.3 kernel 
>>>> without
>>>> any DVB drivers(only the dvb-core) included and installed the CVS
>>>> versions, again only >>> tuning status == 0x00.
>>>>
>>>> So I'm wondering, does this card work at all? I understand that there
>>>> are different versions? Also, all my channels are encrypted with 
>>>> Conax,
>>>> but I do have a CAM and it works in my win machine. Nevertheless, I 
>>>> was
>>>> under the impression, that I should still be able to detect the
>>>> channels, just not watch them, if the CAM part doesn't work?
>>>>
>>>> It's very likely I'm just doing something wrong or missing a step...
>>>>
>>>> Raido
>>>>
>>>> part of dmesg:
>>>>
>>>> Linux video capture interface: v1.00
>>>> bttv: driver version 0.9.16 loaded
>>>> bttv: using 8 buffers with 2080k (520 pages) each for capture
>>>> bttv: Bt8xx card found (0).
>>>> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 19
>>>> ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKB] -> GSI 19 (level,
>>>> low) -> IRQ 17
>>>> bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 17, latency: 64, mmio:
>>>> 0xfaafe000
>>>> bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem 
>>>> ID is
>>>> 1822:0001
>>>> bttv0: using: Twinhan DST + clones [card=113,autodetected]
>>>> bttv0: gpio: en=00000000, out=00000000 in=00f100fd [init]
>>>> bttv0: using tuner=4
>>>> bttv0: add subdevice "dvb0"
>>>> bt878: AUDIO driver version 0.0.0 loaded
>>>> bt878: Bt878 AUDIO function found (0).
>>>> ACPI: PCI Interrupt 0000:02:07.1[A] -> Link [LNKB] -> GSI 19 (level,
>>>> low) -> IRQ 17
>>>> bt878(0): Bt878 (rev 17) at 02:07.1, irq: 17, latency: 64, memory:
>>>> 0xfaaff000
>>>> DVB: registering new adapter (bttv0).
>>>> dst_get_device_id: Recognise [DCT-CI]
>>>>
>>>> DST type flags : 0x1 newtuner 0x2 ts204 0x8 firmware version = 1 0x10
>>>> firmware version = 2
>>>> dst_get_mac: MAC Address=[00:08:ca:16:15:00]
>>>> dst_ca_attach: registering DST-CA device
>>>> DVB: registering frontend 0 (DST DVB-C)...
>>>>




More information about the linux-dvb mailing list