[linux-dvb] Two card config question

Michael Krufky mkrufky at m1k.net
Sun Oct 30 01:08:29 CEST 2005


Philip Prindeville wrote:

>
> via-ircc: dongle probing not supported, please specify dongle_id 
> module parameter.
> IrDA: Registered device irda0 (via-ircc)
> Linux video capture interface: v1.00
> cx2388x v4l2 driver version 0.0.4 loaded
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
> PCI: setting IRQ 12 as level-triggered
> ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 12 (level, 
> low) -> IRQ 12
> cx88[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV 
> [card=22,autodetected]
> tuner 0-0061: chip found @ 0xc2 (cx88[0])
> tuner 0-0061: type set to 52 (Thomson DDT 7610 (ATSC/NTSC))
> cx88[0]/0: found at 0000:00:14.0, rev: 5, irq: 12, latency: 32, mmio: 
> 0xde000000cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
> cx88[0]/0: registered device radio0
> cx2388x dvb driver version 0.0.4 loaded
> ACPI: PCI Interrupt 0000:00:14.2[A] -> Link [LNKB] -> GSI 12 (level, 
> low) -> IRQ 12
> cx88[0]/2: found at 0000:00:14.2, rev: 5, irq: 12, latency: 32, mmio: 
> 0xdf000000cx88[0]/2: cx2388x based dvb card
> DVB: registering new adapter (cx88[0]).
> DVB: registering frontend 0 (pcHDTV HD3000 HDTV)...
> bttv: driver version 0.9.15 loaded
> bttv: using 8 buffers with 2080k (520 pages) each for capture
> bttv: Bt8xx card found (0).
> ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 10 (level, 
> low) -> IRQ 10
> bttv0: Bt878 (rev 17) at 0000:00:13.0, irq: 10, latency: 32, mmio: 
> 0xe0001000
> bttv0: detected: ChainTech digitop DST-1000 DVB-S [card=113], PCI 
> subsystem ID is 270f:fc00
> bttv0: using: Twinhan DST + clones [card=113,autodetected]
> bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
> bttv0: using tuner=4
> bttv0: add subdevice "dvb0"
> bt878: AUDIO driver version 0.0.0 loaded
> bt878: Bt878 AUDIO function found (0).
> ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKA] -> GSI 10 (level, 
> low) -> IRQ 10
> bt878(0): Bt878 (rev 17) at 00:13.1, irq: 10, latency: 32, memory: 
> 0xe0002000
> ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
> PCI: setting IRQ 7 as level-triggered
> ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 7 (level, 
> low) -> IRQ 7
>
> So it looked to me like the card was being detected properly...

[snip]

> So I'm not sure what's going on...  Perhaps udev doesn't correctly 
> support
> more than one DVB adapter?  Is there any way to force which adapter
> numbers get used?

You have to explicitly call:

modprobe dvb-bt8xx
modprobe dst

(this is covered in linux/Documentation/dvb/bt8xx.txt)




More information about the linux-dvb mailing list