[linux-dvb] Stuck with Kworld DVB-T 220 with saa71

Jyrki Majamaki hausberg at mbnet.fi
Mon Apr 3 21:24:21 CEST 2006


Unfortunately it was not such a brilliant idea
I tried the one with mercurian but now even my trusty Nova-T stopped working

ediabox ~ # modprobe cx88xx
WARNING: Error inserting videodev
(/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko):
Input/output error

mediabox ~ # modprobe cx8800
WARNING: Error inserting videodev
(/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko):
Input/output error

This is what I get in dmesg:
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 55778 usecs
intel8x0: clocking to 48000
Linux video capture interface: v1.00
video_dev: unable to get major 81
i2c-core: driver [tveeprom] registered
Linux video capture interface: v1.00
video_dev: unable to get major 81
kobject_register failed for v4l1_compat (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
cx2388x v4l2 driver version 0.0.5 loaded
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKA] -> GSI 5 (level, low)
-> IRQ 5
CORE cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T
[card=18,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
i2c_adapter i2c-0: adapter [cx88[0]] registered
i2c_adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
i2c_adapter i2c-0: master_xfer[0] R, addr=0x50, len=256
tveeprom 0-0050: Hauppauge model 90002, rev C176, serial# 83189
tveeprom 0-0050: MAC address is 00-0D-FE-01-44-F5
tveeprom 0-0050: tuner model is Thompson DTT7592 (idx 76, type 4)
tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 0-0050: audio processor is None (idx 0)
tveeprom 0-0050: decoder processor is CX882 (idx 25)
tveeprom 0-0050: has no radio, has IR remote
cx88[0]: hauppauge eeprom: model=90002
input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input2
cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 5, latency: 64, mmio:
0xfb000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
kobject_register failed for dvb_pll (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
kobject_register failed for dvb_core (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
Linux video capture interface: v1.00
video_dev: unable to get major 81
cx88_dvb: Unknown symbol dvb_pll_thomson_fe6600
cx88_dvb: Unknown symbol dvb_pll_thomson_dtt761x


If I try modprobe saa7134 I get following:

mediabox ~ # modprobe saa7134
WARNING: Error inserting videodev
(/lib/modules/2.6.15.1/kernel/drivers/media/video/videodev.ko):
Input/output error
mediabox ~ # dmesg
red new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
pnp: 00:0b: ioport range 0x680-0x6ff has been reserved
pnp: 00:0b: ioport range 0x295-0x296 has been reserved
PCI: Bridge: 0000:00:08.0
  IO window: disabled.
  MEM window: f8a00000-feafffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: f4900000-f89fffff
  PREFETCH window: c4800000-e47fffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1144098342.700:1): initialized
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NTFS driver 2.1.25 [Flags: R/W DEBUG].
JFS: nTxBlock = 4016, nTxLock = 32128
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [CPU1] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)]
lp0: using parport0 (interrupt-driven).
FDC 0 is a post-1991 82077
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LKLN] -> GSI 3 (level, low)
-> IRQ 3
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ipr: IBM Power RAID SCSI Device Driver version: 2.1.0 (October 31, 2005)
libata version 1.20 loaded.
sata_nv 0000:00:0b.0: version 0.8
ACPI: PCI Interrupt Link [LSHD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LSHD] -> GSI 11 (level, low)
-> IRQ 11
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE882 bmdma 0x7F00 irq 11
ata2: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0x7F08 irq 11
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3e01 87:4023
88:407f
ata1: dev 0 ATA-7, max UDMA/133, 488397168 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ata2: no device found (phy stat 00000000)
scsi1 : sata_nv
  Vendor: ATA       Model: WDC WD2500JS-55N  Rev: 10.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 0
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 5, io mem 0xfebfdc00
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2
(2004/08/27)
usbcore: registered new driver rtl8150
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for
PocketPC PDA
drivers/usb/serial/ipaq.c: USB PocketPC PDA driver v0.5
usbcore: registered new driver ipaq
mice: PS/2 mouse device common for all mice
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.5
wbsd: Copyright(c) Pierre Ossman
oprofile: using timer interrupt.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 212 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost at snowman.net>.
http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PS2K PS2M UAR1  MAC AC97  MDM USB0 USB1 USB2 PCI1
ACPI: (supports S0 S1 S3 S4 S5)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 180k freed
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
Adding 506036k swap on /dev/sda2.  Priority:-1 extents:1 across:506036k
EXT3 FS on sda3, internal journal
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKD] -> GSI 10 (level, low)
-> IRQ 10
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module  1.0-8178  Wed Dec 14
16:22:51 PST 2005
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LAUI] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 55778 usecs
intel8x0: clocking to 48000
Linux video capture interface: v1.00
video_dev: unable to get major 81
i2c-core: driver [tveeprom] registered
Linux video capture interface: v1.00
video_dev: unable to get major 81
kobject_register failed for v4l1_compat (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
cx2388x v4l2 driver version 0.0.5 loaded
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKA] -> GSI 5 (level, low)
-> IRQ 5
CORE cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T
[card=18,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
i2c_adapter i2c-0: adapter [cx88[0]] registered
i2c_adapter i2c-0: master_xfer[0] W, addr=0x50, len=1
i2c_adapter i2c-0: master_xfer[0] R, addr=0x50, len=256
tveeprom 0-0050: Hauppauge model 90002, rev C176, serial# 83189
tveeprom 0-0050: MAC address is 00-0D-FE-01-44-F5
tveeprom 0-0050: tuner model is Thompson DTT7592 (idx 76, type 4)
tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 0-0050: audio processor is None (idx 0)
tveeprom 0-0050: decoder processor is CX882 (idx 25)
tveeprom 0-0050: has no radio, has IR remote
cx88[0]: hauppauge eeprom: model=90002
input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input2
cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 5, latency: 64, mmio:
0xfb000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
kobject_register failed for dvb_pll (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
kobject_register failed for dvb_core (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
Linux video capture interface: v1.00
video_dev: unable to get major 81
cx88_dvb: Unknown symbol dvb_pll_thomson_fe6600
cx88_dvb: Unknown symbol dvb_pll_thomson_dtt761x
spurious 8259A interrupt: IRQ15.
Linux video capture interface: v1.00
video_dev: unable to get major 81
i2c-core: driver [ir-kbd-i2c] registered
kobject_register failed for v4l1_compat (-17)
 [<c0288a1b>] kobject_register+0x6b/0x80
 [<c01344a0>] mod_sysfs_setup+0x50/0xc0
 [<c0135842>] load_module+0x972/0xab0
 [<c014fdd2>] __handle_mm_fault+0x142/0x290
 [<c0135a15>] sys_init_module+0x65/0x210
 [<c01032c5>] syscall_call+0x7/0xb
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 5 (level, low)
-> IRQ 5
saa7133[0]: found at 0000:02:09.0, rev: 208, irq: 5, latency: 64, mmio:
0xfeadf800
saa7133[0]: subsystem: 17de:7201, board: Tevion/KWorld DVB-T 220RF
[card=88,autodetected]
saa7133[0]: board init: gpio is 100
i2c_adapter i2c-1: adapter [saa7133[0]] registered
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x50
i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=0
i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=0
i2c_adapter i2c-1: client [tveeprom] registered with bus id 1-0050
i2c_adapter i2c-1: master_xfer[0] R, addr=0x7a, len=0
i2c_adapter i2c-1: master_xfer[0] R, addr=0x47, len=0
i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x50, len=128
saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
i2c_adapter i2c-1: master_xfer[0] W, addr=0x08, len=3
i2c-core: driver [tuner] registered
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x42
i2c_adapter i2c-1: master_xfer[0] W, addr=0x42, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x43
i2c_adapter i2c-1: master_xfer[0] W, addr=0x43, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x4a
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4a, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x4b
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=0
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x4b, len=1
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x4b, len=1
tuner 1-004b: chip found @ 0x96 (saa7133[0])
i2c_adapter i2c-1: client [(tuner unset)] registered with bus id 1-004b
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] R, addr=0x60, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x61, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x62, len=1
i2c_adapter i2c-1: master_xfer[0] R, addr=0x63, len=1
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
tuner 1-004b: setting tuner address to 61
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] R, addr=0x61, len=1
tuner 1-004b: type set to tda8290+75a
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x61, len=14
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: master_xfer[0] W, addr=0x4b, len=2
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x60
i2c_adapter i2c-1: master_xfer[0] W, addr=0x60, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x61
i2c_adapter i2c-1: master_xfer[0] W, addr=0x61, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x62
i2c_adapter i2c-1: master_xfer[0] W, addr=0x62, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x63
i2c_adapter i2c-1: master_xfer[0] W, addr=0x63, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x64
i2c_adapter i2c-1: master_xfer[0] W, addr=0x64, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x65
i2c_adapter i2c-1: master_xfer[0] W, addr=0x65, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x66
i2c_adapter i2c-1: master_xfer[0] W, addr=0x66, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x67
i2c_adapter i2c-1: master_xfer[0] W, addr=0x67, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x68
i2c_adapter i2c-1: master_xfer[0] W, addr=0x68, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x69
i2c_adapter i2c-1: master_xfer[0] W, addr=0x69, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6a
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6a, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6b
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6b, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6c
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6c, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6d
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6d, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6e
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6e, len=0
i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x6f
i2c_adapter i2c-1: master_xfer[0] W, addr=0x6f, len=0
saa7133[0]: registered device video1 [v4l2]
saa7133[0]: registered device vbi1
saa7133[0]: registered device radio0




> This card works with the CVS version, the card also works with the latest
> git kernel from
> kernel.org.
>
> The remote as yet doesn't work.
>
>
> Jyrki Majamaki wrote:
>> I have Kworld DVB-T 220 and it is evil. It's aDVB-T card
>> with analogue tuner as well.
>>
>> lspci:
>>
>> 02:09.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135
>> Video
>> Broadcast Decoder (rev d0)
>>
>> Following kernel modules at least sound related:
>> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa6752hs.ko
>> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-alsa.ko
>> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-dvb.ko
>> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134-empress.ko
>> /lib/modules/2.6.15.1/kernel/drivers/media/video/saa7134/saa7134.ko
>>
>> Ok first modprobe saa7134:
>> i2c-core: driver [ir remote kbd driver] registered
>> saa7130/34: v4l2 driver version 0.2.14 loaded
>> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
>> ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKB] -> GSI 5 (level, low)
>> ->
>> IRQ 5
>> saa7133[0]: found at 0000:02:09.0, rev: 208, irq: 5, latency: 64, mmio:
>> 0xfeadf800
>> saa7133[0]: subsystem: 17de:7201, board: UNKNOWN/GENERIC
>> [card=0,autodetected]
>> saa7133[0]: board init: gpio is 100
>> i2c_adapter i2c-1: adapter [saa7133[0]] registered
>> i2c_adapter i2c-1: master_xfer[0] R, addr=0x7a, len=0
>> i2c_adapter i2c-1: master_xfer[0] R, addr=0x47, len=0
>> i2c_adapter i2c-1: master_xfer[0] W, addr=0x50, len=1
>> i2c_adapter i2c-1: master_xfer[0] R, addr=0x50, len=128
>> saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> ff
>> saa7133[0]: registered device video1 [v4l2]
>> saa7133[0]: registered device vbi1
>>
>> modprobe saa7134-empress:
>> nothing
>>
>> modprobe saa6725hs:
>> i2c-core: driver [i2c saa6752hs MPEG encoder] registered
>> i2c_adapter i2c-1: found normal entry for adapter 1, addr 0x20
>> i2c_adapter i2c-1: master_xfer[0] W, addr=0x20, len=0
>>
>> modprobe saa7134-dvb:
>> nothing (unfortunately I guess)
>>
>> modprobe saa7134-alsa:
>> saa7134 ALSA driver for DMA sound loaded
>> saa7133[0]/alsa: saa7133[0] at 0xfeadf800 irq 5 registered as card -1
>>
>> I don't know what this alsa is looking in that card for...there is also
>> a
>> radio tuner there so maybe
>> something to do with it...
>>
>> lsmod looks like:
>> Module Size Used by
>> saa7134_alsa 10912 0
>> saa7134_dvb 10372 0
>> tda1004x 15172 1 saa7134_dvb
>> saa6752hs 8460 0
>> saa7134_empress 7108 0
>> saa7134 109728 3 saa7134_alsa,saa7134_dvb,saa7134_empress
>> ir_kbd_i2c 6604 1 saa7134
>> snd_pcm_oss 49696 0
>> snd_mixer_oss 17152 1 snd_pcm_oss
>> snd_seq_oss 32320 0
>> snd_seq_midi_event 6080 1 snd_seq_oss
>> snd_seq 50128 4 snd_seq_oss,snd_seq_midi_event
>> snd_seq_device 6860 2 snd_seq_oss,snd_seq
>> snd_intel8x0 29596 0
>> snd_ac97_codec 92384 1 snd_intel8x0
>> snd_ac97_bus 1792 1 snd_ac97_codec
>> snd_pcm 82824 4 saa7134_alsa,snd_pcm_oss,snd_intel8x0,snd_ac97_codec
>> snd_timer 22084 2 snd_seq,snd_pcm
>> snd 47076 10
>>
saa7134_alsa,snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
>> soundcore 7840 1 snd
>> snd_page_alloc 8456 2 snd_intel8x0,snd_pcm
>> cx88_dvb 7684 0
>> mt352 6212 2 saa7134_dvb,cx88_dvb
>> or51132 9284 1 cx88_dvb
>> video_buf_dvb 4548 2 saa7134_dvb,cx88_dvb
>> nxt200x 14724 2 saa7134_dvb,cx88_dvb
>> lgdt330x 7708 1 cx88_dvb
>> cx22702 6020 1 cx88_dvb
>> cx8802 9220 1 cx88_dvb
>> cx8800 28300 0
>> cx88xx 55712 3 cx88_dvb,cx8802,cx8800
>> video_buf 17284 9
>>
saa7134_alsa,saa7134_dvb,saa7134_empress,saa7134,cx88_dvb,video_buf_dvb,cx8802,cx8800,cx88xx
>> ir_common 8132 3 saa7134,ir_kbd_i2c,cx88xx
>> btcx_risc 3976 3 cx8802,cx8800,cx88xx
>> tveeprom 13776 1 cx88xx
>> nvidia 4083664 12
>>
>> I could try modprobe with different card options but I am not sure
>> whether
>> this is going to help other than with analogue tuner.
>>
>> The mentioned cx88 modules come from my second card Hauppage Nova-T
>> (works
>> like a charm)
>>
>>
>> _______________________________________________
>> linux-dvb mailing list
>> linux-dvb at linuxtv.org
>> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>
>>
>>
>
>
>





More information about the linux-dvb mailing list