[linux-dvb] Re: DViCO Dual Digital 2 remote control

Damien Phillip Morrissey dpm95 at uow.edu.au
Mon Dec 11 23:06:31 CET 2006


I, too, have the same problem.  Running a DVico Dual Digital 2 in my MythTV box I get no response for the remote using evtest or cat. 

I am running mythtv on Ubuntu Fiesty (Development), but had exactly the same problem with Edgy. 

Could it have something to do with the remote being registered twice?  Because it is a dual tuner, it also registers its remote twice. 

>From cat /proc/bus/input/devices I get the following: 

I: Bus=0003 Vendor=062a Product=0102 Version=0100 
N: Name="MOSART Semi. Wireless Keyboard & Mouse" 
P: Phys=usb-0000:00:0b.0-5/input0 
S: Sysfs=/class/input/input0 
H: Handlers=kbd event0 
B: EV=120003 
B: KEY=1000000000007 ff87207ac14057ff febeffdfffefffff fffffffffffffffe 
B: LED=7 

I: Bus=0003 Vendor=062a Product=0102 Version=0100 
N: Name="MOSART Semi. Wireless Keyboard & Mouse" 
P: Phys=usb-0000:00:0b.0-5/input1 
S: Sysfs=/class/input/input1 
H: Handlers=kbd mouse0 event1 ts0 
B: EV=f 
B: KEY=c0002 40000000000 1f1fe3 f8000078400 6639fad871d7ad 9e000000000000 0 
B: REL=143 
B: ABS=100000000 

I: Bus=0010 Vendor=001f Product=0001 Version=0100 
N: Name="PC Speaker" 
P: Phys=isa0061/input0 
S: Sysfs=/class/input/input2 
H: Handlers=kbd event2 
B: EV=40001 
B: SND=6 

I: Bus=0003 Vendor=0fe9 Product=db59 Version=0300 
N: Name="IR-receiver inside an USB DVB receiver" 
P: Phys=usb-0000:03:08.2-1/ir0 
S: Sysfs=/class/input/input3 
H: Handlers=kbd event3 
B: EV=3 
B: KEY=c00a4 218305100000000 0 110000 1b840002841 1e168000000000 10008ffc 

I: Bus=0003 Vendor=0fe9 Product=db59 Version=0300 
N: Name="IR-receiver inside an USB DVB receiver" 
P: Phys=usb-0000:03:08.2-2/ir0 
S: Sysfs=/class/input/input4 
H: Handlers=kbd event4 
B: EV=3 
B: KEY=c00a4 218305100000000 0 110000 1b840002841 1e168000000000 10008ffc 

I also have the following (relevant) messages in the /var/log/messages file: 
Dec 10 16:31:58 htpc-server kernel: [   40.027225] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual Digital 2' in cold state, will try to load a firmware 
Dec 10 16:31:58 htpc-server kernel: [   40.182722] dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw' 
Dec 10 16:31:58 htpc-server kernel: [   40.291913] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20 
Dec 10 16:31:58 htpc-server kernel: [   40.291925] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 20 (level, low) -> IRQ 20 
Dec 10 16:31:58 htpc-server kernel: [   40.326586] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual Digital 2' in cold state, will try to load a firmware 
Dec 10 16:31:58 htpc-server kernel: [   40.328747] dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw' 
Dec 10 16:31:58 htpc-server kernel: [   40.382221] usb 3-1: USB disconnect, address 2 
Dec 10 16:31:58 htpc-server kernel: [   40.382252] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. 
Dec 10 16:31:58 htpc-server kernel: [   40.502090] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... 
Dec 10 16:31:58 htpc-server kernel: [   40.510144] usbcore: registered new interface driver dvb_usb_cxusb 
Dec 10 16:31:58 htpc-server kernel: [   40.633989] usb 3-2: USB disconnect, address 3 
Dec 10 16:31:58 htpc-server kernel: [   40.634021] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected. 
Dec 10 16:31:58 htpc-server kernel: [   40.796267] fuse init (API version 7.7) 
Dec 10 16:31:58 htpc-server kernel: [   40.827314] lp0: using parport0 (interrupt-driven). 
Dec 10 16:31:58 htpc-server kernel: [   40.911548] Adding 3004112k swap on /dev/disk/by-uuid/bae9f8c6-54ff-459a-bc4d-99ac2f2dcd2b.  Priority:-1 extents:1 across:3004112k 
Dec 10 16:31:58 htpc-server kernel: [   41.089847] EXT3 FS on hda1, internal journal 
Dec 10 16:31:58 htpc-server kernel: [   42.132398] usb 3-1: new high speed USB device using ehci_hcd and address 4 
Dec 10 16:31:58 htpc-server kernel: [   42.269730] usb 3-1: configuration #1 chosen from 1 choice 
Dec 10 16:31:58 htpc-server kernel: [   42.269950] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual Digital 2' in warm state. 
Dec 10 16:31:58 htpc-server kernel: [   42.270052] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. 
Dec 10 16:31:58 htpc-server kernel: [   42.280685] DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual Digital 2). 
Dec 10 16:31:58 htpc-server kernel: [   42.342605] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)... 
Dec 10 16:31:58 htpc-server kernel: [   42.343139] input: IR-receiver inside an USB DVB receiver as /class/input/input3 
Dec 10 16:31:58 htpc-server kernel: [   42.343167] dvb-usb: schedule remote query interval to 150 msecs. 
Dec 10 16:31:58 htpc-server kernel: [   42.343170] dvb-usb: DViCO FusionHDTV DVB-T Dual Digital 2 successfully initialized and connected. 
Dec 10 16:31:58 htpc-server kernel: [   42.583943] usb 3-2: new high speed USB device using ehci_hcd and address 5 
Dec 10 16:31:58 htpc-server kernel: [   42.721224] usb 3-2: configuration #1 chosen from 1 choice 
Dec 10 16:31:58 htpc-server kernel: [   42.721446] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual Digital 2' in warm state. 
Dec 10 16:31:58 htpc-server kernel: [   42.721533] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. 
Dec 10 16:31:58 htpc-server kernel: [   42.732168] DVB: registering new adapter (DViCO FusionHDTV DVB-T Dual Digital 2). 
Dec 10 16:31:58 htpc-server kernel: [   42.734494] DVB: registering frontend 1 (Zarlink ZL10353 DVB-T)... 
Dec 10 16:31:58 htpc-server kernel: [   42.735038] input: IR-receiver inside an USB DVB receiver as /class/input/input4 
Dec 10 16:31:58 htpc-server kernel: [   42.735063] dvb-usb: schedule remote query interval to 150 msecs. 
Dec 10 16:31:58 htpc-server kernel: [   42.735066] dvb-usb: DViCO FusionHDTV DVB-T Dual Digital 2 successfully initialized and connected. 

Hope this helps whoever may be able to help us! 

Damien. 




More information about the linux-dvb mailing list