[linux-dvb] Tevion DVBT-220RF

Hartmut Hackmann hartmut.hackmann at t-online.de
Sun Jan 15 22:36:56 CET 2006


Hi, Peter

Peter Hartshorn wrote:
> Hartmut Hackmann wrote:
> 
>> HI, Peter
>>
>> Peter Hartshorn wrote:
>>
>>> A couple of days ago I purchased the above mentioned card. What I 
>>> have since found is that this card is not supported under linux. My 
>>> goal is to get it going in Linux. I have uploaded photos of the front 
>>> and the back to image shack. the urls are below.
>>>
>>> http://img297.imageshack.us/img297/3604/front2cn.jpg
>>> http://img82.imageshack.us/img82/1152/back9ah.jpg
>>>
>>> I have included output from the following :
>>>
>>> lspci -v
>>>
>>> 0000:01:08.0 Multimedia controller: Philips Semiconductors SAA7133 
>>> Audio+video broadcast decoder (rev d0)
>>>         Subsystem: Unknown device 17de:7201
>>>         Flags: bus master, medium devsel, latency 64, IRQ 6
>>>         Memory at e4000000 (32-bit, non-prefetchable) [size=2K]
>>>         Capabilities: [40] Power Management version 2
>>>
>>> If any more information is required, feel free to email.
>>>
>> I can't identify all chip types on the card. I assume
>> 2*TDA8275A
>> TDA10046
>> SAA7131
>> Is that right? Especially the exact types of the chips close to the
>> antenna sockets are important. I also need the kernel log messages
>> (dmesg) when the saa7134 module loads.
>> Analog TV and radio might work when you force the card type 81.
>>
>> Best regards
>>    Hartmut
>>
>>
>>
> 
> The two small chips are Philips 8275AC1
> The single large one to the right of the small ones is the TDA10046A
> The large one toward the pci connection is the SAA7131E.
> 
> With card=81 analog tv works.
> 
> dmesg output:
> 
> saa7130/34: v4l2 driver version 0.2.14 loaded
> ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKC] -> GSI 6 (level, low) 
> -> IRQ 6
> saa7133[0]: found at 0000:01:08.0, rev: 208, irq: 6, latency: 64, mmio: 
> 0xe4000000
> saa7133[0]: subsystem: 17de:7201, board: Philips Tiger reference design 
> [card=81,insmod option]
> saa7133[0]: board init: gpio is 20100
> saa7133[0]: i2c eeprom 00: de 17 01 72 ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> tuner 0-004b: chip found @ 0x96 (saa7133[0])
> tuner 0-004b: setting tuner address to 61
> tuner 0-004b: tuner: type set to tda8290+75a
> saa7133[0]: registered device video0 [v4l2]
> saa7133[0]: registered device vbi0
> 
Ok, if analog works, it should not be too difficult tu get dvb-t working as
well. You need to load the saa7134-dvb module. If you do and try a dvb
application, do you get a "pll set failed" message in the kernel log?
If i give you some instructions, are you able to help yourself?

Best regards
    Hartmut



More information about the linux-dvb mailing list