[linux-dvb] Compro DVB-T200 - saa7134-dvb Doesn't Work.

raid517 at ukonline.co.uk raid517 at ukonline.co.uk
Mon Jan 16 19:53:27 CET 2006


Hi I am using Debian Kanotix (Sid Unstable) with all the latest updates 
and kernel 2.6.15.1. I have a Compro DVB-T200 - saa7134-dvb vased card - 
but for some reason this does not appear to work.

I was previously using a nova-t budget card - and this worked very well, 
so much so indeed that it required pretty much zero configuration 
(especially in Kaffiene) and worked more or less out of the box - but I 
gave that to my nephew as a gift included with a new PC over Xmas.

My dmesg and lsmod output for the saa7134 card are attached. The driver 
appears to load fine, with no difficulties whatsoever - and I even have 
the correct firmware installed by default - which I think is 
dvb-fe-tda100046.fm (although there is no evidence in dmesg of this 
being uploaded).

However there is nothing listed in my /dev section under DVB (such as 
/dev/dvb/video0, or /dev/dvb/adapter0 and so on). Indeed there are no 
DVB enteries in my /dev directory at all. (In the past these were always 
automatically created for me).

Can anyone advise how best to get this card working? Is it likely that 
this card will this card ever work out of the box in the same way that 
my nova-t tv card did?

GJ
-------------- next part --------------

rrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
Generic PHY: Registered new driver
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev at vger.kernel.org cc hadi at cyberus.ca)
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4800-0x487f has been reserved
pnp: 00:00: ioport range 0x4880-0x48ff has been reserved
PCI: Bridge: 0000:00:0b.0
  IO window: d000-dfff
  MEM window: fdf00000-fdffffff
  PREFETCH window: e8000000-f7ffffff
PCI: Bridge: 0000:00:0e.0
  IO window: c000-cfff
  MEM window: fde00000-fdefffff
  PREFETCH window: fdd00000-fddfffff
PCI: Setting latency timer of device 0000:00:0e.0 to 64
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
vesafb: framebuffer at 0xf0000000, mapped to 0xe0880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:ab90
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
vesafb: Mode is VGA compatible
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xe800-0xe807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe808-0xe80f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6B200P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY DVD-ROM DDU1612, ATAPI CD/DVD-ROM drive
hdd: PIONEER DVD-RW DVR-109, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 398297088 sectors (203928 MB) w/8192KiB Cache, CHS=24792/255/63, UDMA(133)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 hda6 hda7 > hda3
hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
3ware Storage Controller device driver for Linux v1.26.02.001.
3ware 9000 Storage Controller device driver for Linux v2.26.02.004.
libata version 1.20 loaded.
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid10 personality registered as nr 9
md: raid5 personality registered as nr 4
raid5: automatically using best checksumming function: pIII_sse
   pIII_sse  :  7602.000 MB/sec
raid5: using function: pIII_sse (7602.000 MB/sec)
raid6: int32x1    921 MB/s
raid6: int32x2    984 MB/s
raid6: int32x4    739 MB/s
raid6: int32x8    662 MB/s
raid6: mmxx1     1972 MB/s
raid6: mmxx2     3436 MB/s
raid6: sse1x1    1566 MB/s
raid6: sse1x2    2559 MB/s
raid6: sse2x1    2672 MB/s
raid6: sse2x2    3801 MB/s
raid6: using algorithm sse2x2 (3801 MB/s)
md: raid6 personality registered as nr 8
md: multipath personality registered as nr 7
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
device-mapper: dm-multipath version 1.0.4 loaded
device-mapper: dm-round-robin version 1.0.0 loaded
device-mapper: dm-emc version 0.0.3 loaded
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
EISA: Detected 0 cards.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 8192 (order: 3, 32768 bytes)
TCP established hash table entries: 32768 (order: 5, 131072 bytes)
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 276k freed
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, ma
x batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: Using r5 hash to sort names
usbcore: registered new driver usbfs
usbcore: registered new driver hub
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 256M @ 0xd0000000
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 5, io mem 0xfe02f000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUBB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUBB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: irq 10, io mem 0xfe02e000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
input: PC Speaker as /class/input/input1
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
usb 1-1: new full speed USB device using ohci_hcd and address 2
gameport: EMU10K1 is pci0000:02:07.1/gameport0, io 0xc800, speed 1193kHz
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [LNK5] -> GSI 11 (level, low) -> IRQ 11
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xe0850000, 00:11:09:c7:24:91, IRQ 11
Initializing USB Mass Storage driver...
usb 1-2: new full speed USB device using ohci_hcd and address 3
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNK3] -> GSI 3 (level, low) -> IRQ 3
saa7130[0]: found at 0000:02:08.0, rev: 1, irq: 3, latency: 32, mmio: 0xfdefe000
saa7130[0]: subsystem: 185b:c901, board: Compro Videomate DVB-T200 [card=71,autodetected]
saa7130[0]: board init: gpio is 843f00
input: saa7134 IR (Compro Videomate DV as /class/input/input2
usb 1-2: configuration #1 chosen from 2 choices
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
saa7130[0]: i2c eeprom 00: 5b 18 01 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7130[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 20: 01 40 01 03 03 ff 03 01 08 ff 00 88 ff ff ff ff
saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 40: ff d0 00 c2 86 10 ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb
saa7130[0]: i2c eeprom 60: 30 26 ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7130[0]: registered device video0 [v4l2]
saa7130[0]: registered device vbi0
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
usb 2-3: new full speed USB device using ohci_hcd and address 2
ACPI: PCI Interrupt 0000:02:07.2[B] -> Link [LNK3] -> GSI 3 (level, low) -> IRQ 3
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[3]  MMIO=[fdeff000-fdeff7ff]  Max Packet=[2048]
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUB2] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: irq 11, io mem 0xfe02d000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb 2-3: unable to read config index 0 descriptor/all
usb 2-3: can't read configurations, error -110
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
usb 1-1: USB disconnect, address 2
usb 1-2: USB disconnect, address 3
input: ImPS/2 Generic Wheel Mouse as /class/input/input3
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
usb 3-1: new high speed USB device using ehci_hcd and address 2
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 5
ACPI: PCI Interrupt 0000:02:07.0[A] -> <6>scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Link [LNK2] -> GSI 5 (level, low) -> IRQ 5
Installing spdif_bug patch: Audigy 2 [SB0240]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c01010072f5]
usb 3-2: new high speed USB device using ehci_hcd and address 3
usb 3-2: configuration #1 chosen from 2 choices
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ohci_hcd 0000:00:02.1: wakeup
usb 2-3: new full speed USB device using ohci_hcd and address 4
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 2 ports detected
usb 2-3.1: new full speed USB device using ohci_hcd and address 5
eth1394: $Rev: 1312 $ Ben Collins <bcollins at debian.org>
eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
usb 2-3.2: new full speed USB device using ohci_hcd and address 6
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 0 alt 0 proto 2 vid 0x043D pid 0
x007B
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
  Vendor: USB 2.0   Model: Storage Device    Rev: 0100
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
 sda: sda1
sd 2:0:0:0: Attached scsi disk sda
sd 2:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
  Vendor: Apple     Model: iPod              Rev: 1.62
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdb: 117210240 512-byte hdwr sectors (60012 MB)
sdb: Write Protect is off
sdb: Mode Sense: 6c 00 00 08
sdb: assuming drive cache: write through
SCSI device sdb: 117210240 512-byte hdwr sectors (60012 MB)
sdb: Write Protect is off
sdb: Mode Sense: 6c 00 00 08
sdb: assuming drive cache: write through
 sdb: sdb1 sdb2
sd 3:0:0:0: Attached scsi removable disk sdb
sd 3:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
Adding 979924k swap on /dev/hda5.  Priority:-1 extents:1 across:979924k
Capability LSM initialized
fuse init (API version 7.3)
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNK1] -> GSI 10 (level, low) -> IRQ 10
[fglrx] module loaded - fglrx 8.20.8 [Dec  6 2005] on minor 0
[fglrx] ACPI power management is initialized.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
r8169: lan1: link up
NET: Registered protocol family 17
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
lp0: using parport0 (interrupt-driven).
lp0: console ready
raid517 at linux1:~$
(CM) [PWRB]
lp0: using parport
-------------- next part --------------
Module                  Size  Used by
lp                      9672  0
video                  14212  0
thermal                10888  0
processor              19008  1 thermal
fan                     3460  0
container               3328  0
button                  5008  0
battery                 7684  0
ac                      3460  0
af_packet              16904  2
fglrx                 427136  0
fuse                   32012  0
capability              3208  0
commoncap               5248  1 capability
usblp                  10752  0
eth1394                17416  0
snd_emu10k1_synth       6144  0
snd_emux_synth         33536  1 snd_emu10k1_synth
snd_seq_virmidi         5504  1 snd_emux_synth
snd_seq_midi_emul       6144  1 snd_emux_synth
snd_seq_dummy           2820  0
snd_seq_oss            29440  0
snd_seq_midi            6528  0
snd_seq_midi_event      6016  3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
snd_seq                45808  9 snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_emu10k1           108676  2 snd_emu10k1_synth
snd_rawmidi            20096  3 snd_seq_virmidi,snd_seq_midi,snd_emu10k1
snd_ac97_codec         86432  1 snd_emu10k1
snd_ac97_bus            1920  1 snd_ac97_codec
parport_pc             35908  1
snd_pcm_oss            47104  0
snd_mixer_oss          15488  1 snd_pcm_oss
snd_pcm                76040  3 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
parport                30536  2 lp,parport_pc
8250_pnp                8448  0
8250                   17940  1 8250_pnp
serial_core            17536  1 8250
ehci_hcd               30344  0
snd_seq_device          6796  8 snd_emu10k1_synth,snd_emux_synth,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_emu10k1,snd_rawmidi
psmouse                32388  0
snd_timer              20740  3 snd_seq,snd_emu10k1,snd_pcm
snd_page_alloc          8072  2 snd_emu10k1,snd_pcm
snd_util_mem            3456  2 snd_emux_synth,snd_emu10k1
snd_hwdep               7044  2 snd_emux_synth,snd_emu10k1
snd                    44804  15 snd_emux_synth,snd_seq_virmidi,snd_seq_oss,snd_seq,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_device,snd_timer,snd_hwdep
ohci1394               30772  0
ieee1394              284984  2 eth1394,ohci1394
serio_raw               5508  0
saa7134               106208  0
video_buf              17028  1 saa7134
v4l2_common             4864  1 saa7134
v4l1_compat            13572  1 saa7134
ir_kbd_i2c              6540  1 saa7134
ir_common               8068  2 saa7134,ir_kbd_i2c
videodev                7296  1 saa7134
usb_storage            68416  0
pcspkr                  1668  0
emu10k1_gp              2816  0
gameport               11400  2 emu10k1_gp
r8169                  23816  0
soundcore               7392  1 snd
ohci_hcd               19076  0
amd64_agp               9668  1
agpgart                27464  2 fglrx,amd64_agp
shpchp                 40256  0
pci_hotplug            24372  1 shpchp
i2c_nforce2             5632  0
usbcore               109956  5 usblp,ehci_hcd,usb_storage,ohci_hcd
evdev                   7424  0 8250
ehci_hcd               30344  0


More information about the linux-dvb mailing list