[linux-dvb] Syslog is flooded with debug messages of Pinnacle PCTV

Helmut Auer vdr at helmutauer.de
Tue Jun 13 23:01:59 CEST 2006


Helmut Auer schrieb:
> Hello,
> In dvb-bt8xx there are at least 3 printk statements which are flooding 
> the syslog with a lot of messages.
> Please remove thes from the hg repository.
> 
Hi,
shall I send a patch for this ? I think a patch for it was already posted sometimes by the 
"famous" Uwe Bugla ;)



-- 
Helmut Auer, helmut at helmutauer.de

--- /drivers/media/dvb/bt8xx/dvb-bt8xx.c Tue 21 Feb 13:47:00 2006
+++ /drivers/media/dvb/bt8xx/dvb-bt8xx.c Tue 21 Feb 17:29:00 2006
@@ -52,8 +52,6 @@
  {
  	struct dvb_bt8xx_card *card = (struct dvb_bt8xx_card *)data;

-	//printk("%d ", card->bt->finished_block);
-
  	while (card->bt->last_block != card->bt->finished_block) {
  		(card->bt->TS_Size ? dvb_dmx_swfilter_204 : dvb_dmx_swfilter)
  			(&card->demux,
@@ -80,8 +78,7 @@
  	card->nfeeds++;
  	rc = card->nfeeds;
  	if (card->nfeeds == 1)
-		bt878_start(card->bt, card->gpio_mode,
-			    card->op_sync_orin, card->irq_err_ignore);
+		bt878_start(card->bt, card->gpio_mode);
  	up(&card->lock);
  	return rc;
  }
@@ -198,7 +195,7 @@
  		0x00120000,0x00140000};

  	#define XTAL 1011100 /* Hz, really 1.0111 MHz and a /10 prescaler */
-	printk("cx24108 debug: entering SetTunerFreq, freq=%d\n",freq);
+	dprintk("cx24108 debug: entering SetTunerFreq, freq=%d\n",freq);

  	/* This is really the bit driving the tuner chip cx24108 */

@@ -209,7 +206,7 @@

  	/* decide which VCO to use for the input frequency */
  	for(i=1;(i<sizeof(osci)/sizeof(osci[0]))&&(osci[i]<freq);i++);
-	printk("cx24108 debug: select vco #%d (f=%d)\n",i,freq);
+	dprintk("cx24108 debug: select vco #%d (f=%d)\n",i,freq);
  	band=bandsel[i];
  	/* the gain values must be set by SetSymbolrate */
  	/* compute the pll divider needed, from Conexant data sheet,
@@ -225,7 +222,7 @@
  	    ((a&0x1f)<<11);
  	/* everything is shifted left 11 bits to left-align the bits in the
  	   32bit word. Output to the tuner goes MSB-aligned, after all */
-	printk("cx24108 debug: pump=%d, n=%d, a=%d\n",pump,n,a);
+	dprintk("cx24108 debug: pump=%d, n=%d, a=%d\n",pump,n,a);
  	cx24110_pll_write(fe,band);
  	/* set vga and vca to their widest-band settings, as a precaution.
  	   SetSymbolrate might not be called to set this up */




More information about the linux-dvb mailing list