[linux-dvb] Skystar2: Different PCI-ID

Yvan Gosset ygosset at free.fr
Sun Nov 26 00:19:56 CET 2006


Hello.

Yes, there is chance, but not with your kernel-dvd (or v4l-dvb) version,
and not quickly I think.(because I2C errors)

It's necessary to know which IC chips there are on board:
- flexcop B2C2 ?
- tuner ??
(eeprom, less, can be small)

What is your kernel version ?

Yvan.

Le Samedi 25 Novembre 2006 22:08, Bernhard Huafbauer a écrit :
> Hello,
> I have a Skystar2 Rev 2.3. (http://home.vrweb.de/~bernhardu/skystar2.jpg)
>
> A 'lspci -nn' shows me this:
> 00:07.0 Network controller [0280]: Techsan Electronics Co Ltd Unknown
> device [13d0:2102] (rev 01)
>
> But in flexcop-pci.c is only 13d0:2103 mentioned and mine is 13d0:2102.
>
> When I change flexcop-pci.c about line 402 to look like this
>
> 	static struct pci_device_id flexcop_pci_tbl[] = {
> 		{ PCI_DEVICE(0x13d0, 0x2103) },
> 		{ PCI_DEVICE(0x13d0, 0x2102) },
> 	/*	{ PCI_DEVICE(0x13d0, 0x2200) }, ? */
> 		{ },
> 	};
>
> I get following output from dmesg:
>
> 	b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded
> successfully flexcop-pci: will use the HW PID filter.
> 	flexcop-pci: card revision 1
> 	PCI: Enabling device 0000:00:07.0 (0000 -> 0003)
> 	ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 209
> 	DVB: registering new adapter (FlexCop Digital TV device).
> 	b2c2-flexcop: reading of MAC address failed.
> 	i2c_adapter i2c-4: SMBus Quick command not supported, can't probe for
> chips b2c2-flexcop: i2c master_xfer failed
> 	b2c2-flexcop: i2c master_xfer failed
> 	b2c2-flexcop: i2c master_xfer failed
> 	mt352_read_register: readreg error (reg=127, ret==-121)
> 	b2c2-flexcop: i2c master_xfer failed
> 	nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
> 	Unknown/Unsupported NXT chip: 00 00 00 00 00
> 	b2c2-flexcop: i2c master_xfer failed
> 	lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
> 	b2c2-flexcop: i2c master_xfer failed
> 	b2c2-flexcop: i2c master_xfer failed
> 	stv0297_readreg: readreg error (reg == 0x80, ret == -121)
> 	b2c2-flexcop: i2c master_xfer failed
> 	mt312_read: ret == -121
> 	b2c2-flexcop: no frontend driver found for this B2C2/FlexCop adapter
> 	ACPI: PCI interrupt for device 0000:00:07.0 disabled
>
>
> Is there any chance to get this card supported?
>
> Kind regards
> Bernhard
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb



More information about the linux-dvb mailing list