[linux-dvb] DVB devices fails after kernel.i686 2.6.20-1.2925.fc6

Paul Wilson paul at wilsononline.id.au
Fri Apr 6 02:14:15 CEST 2007


I have two DVB devices but one of these fails to initialise after I
update my FC6 kernel, I'm pretty sure its the Air2PC/AirStar 2 DVB-T PCI
card.
I have regressed back to  kernel.i686 2.6.19-1.2911.6.5.fc6 which brings
my devices back online.

I have pasted the /var/log/dmesg output for both working and broken
kernel below
The most interesting message is :
**WARNING** I2C adapter driver [B2C2 FlexCop device] forgot to specify
physical device; fix it!

Any hints on what this means and if this can be fixed? or do I need to
make some changes in my modules.conf??

Thanks

FC6 Kernel 2911 (working)

b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded
successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level,
low) -> IRQ 20
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0a:33:62
ieee1394: Initialized config rom entry `ip1394'
b2c2-flexcop: i2c master_xfer failed
cx2388x v4l2 driver version 0.0.6 loaded
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI'
bus controlled by a 'FlexCopIIb' complete


FC6 Kernel 2933: (not working)
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded
successfully
Linux video capture interface: v2.00
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
/8]
CORE cx88[0]: subsystem: 1822:0025, board: digitalnow DNTV Live! DVB-T
Pro [card=42,insmod option]
TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe
cx2388x v4l2 driver version 0.0.6 loaded
input: cx88 IR (digitalnow DNTV Live!  as /class/input/input4
cx88[0]/2: cx2388x 8802 Driver Manager
cx88[0]/2: found at 0000:01:08.2, rev: 5, irq: 21, latency: 32, mmio:
0xf6000000
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0a:33:62
**WARNING** I2C adapter driver [B2C2 FlexCop device] forgot to specify
physical device; fix it!
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI'
bus controlled by a 'FlexCopIIb' complete




More information about the linux-dvb mailing list