[linux-dvb] Freecom DVB 25451-Rev.3 Why have it 2 frontends?

[arph at gmx.net]

hello,

after plugin the freecom 25451 rev3 i can see this dmesg-output:



[  136.488000] usb 5-3: new high speed USB device using ehci_hcd and
address 4
[  136.628000] usb 5-3: configuration #1 chosen from 1 choice
[  136.760000] dvb-usb: found a 'WideView WT-220U PenType Receiver
(Typhoon/Freecom)' in cold state, will try to load a firmware
[  136.772000] dvb-usb: downloading firmware from file
'dvb-usb-wt220u-fc03.fw'
[  136.860000] usbcore: registered new interface driver dvb_usb_dtt200u
[  138.260000] usb 5-3: USB disconnect, address 4
[  138.260000] dvb-usb: generic DVB-USB module successfully
deinitialized and disconnected.
[  139.508000] usb 5-3: new high speed USB device using ehci_hcd and
address 5
[  139.640000] usb 5-3: configuration #1 chosen from 1 choice
[  139.640000] dvb-usb: found a 'WideView WT-220U PenType Receiver
(Typhoon/Freecom)' in warm state.
[  139.640000] dvb-usb: will use the device's hardware PID filter (table
count: 15).
[  139.644000] DVB: registering new adapter (WideView WT-220U PenType
Receiver (Typhoon/Freecom)).
[  139.644000] DVB: registering frontend 0 (WideView USB DVB-T)...
[  139.644000] input: IR-receiver inside an USB DVB receiver as
/class/input/input9
[  139.644000] dvb-usb: schedule remote query interval to 300 msecs.
[  139.644000] dvb-usb: WideView WT-220U PenType Receiver
(Typhoon/Freecom) successfully initialized and connected.
[  139.644000] dvb-usb: found a 'WideView WT-220U PenType Receiver
(Typhoon/Freecom)' in warm state.
[  139.644000] dvb-usb: will use the device's hardware PID filter (table
count: 15).
[  139.644000] DVB: registering new adapter (WideView WT-220U PenType
Receiver (Typhoon/Freecom)).
[  139.644000] DVB: registering frontend 1 (WideView USB DVB-T)...
[  139.644000] input: IR-receiver inside an USB DVB receiver as
/class/input/input10
[  139.644000] dvb-usb: schedule remote query interval to 300 msecs.
[  139.644000] dvb-usb: WideView WT-220U PenType Receiver
(Typhoon/Freecom) successfully initialized and connected.
[  139.816000] usbcore: registered new interface driver hiddev
[  139.816000] usbcore: registered new interface driver usbhid
[  139.816000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[  139.832000] usbcore: registered new interface driver xpad
[  139.832000] drivers/usb/input/xpad.c: driver for Xbox controllers v0.1.6
[  141.244000] eth1: no IPv6 routers present
[  141.944000] dvb-usb: recv bulk message failed: -110



in kaffeine there are also 2 devices shown, but i think i only should
have one of it?

Can somebody explain this to me please.

Also in kaffeine, when starting tv the first time, tv-screen freezes
after 2 seconds and i have to switch to another channel, i think it is
some problem with the firmware, because i also have a yakumo and
everthing is fine.