[linux-dvb] Leadtek WinFast HDTV Cinenma

[Jay Mack Newby]

The decoder/bridge IC reads "saa7133HL/101"

The 18 pin IC reads

"A T8P56S
  HBIHG 709"

After running lshal I got

udi = '/org/freedesktop/Hal/devices/pci_1131_7133'
   info.bus = 'pci'  (string)
   info.linux.driver = 'saa7134'  (string)
   info.parent = '/org/freedesktop/Hal/devices/pci_10de_26f'  (string)
   info.product = 'SAA7133/SAA7135 Video Broadcast Decoder'  (string)
   info.subsystem = 'pci'  (string)
   linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:10.0/0000:04:08.0' 
(string)
   pci.device_class = 4  (0x4)  (int)
   pci.device_protocol = 0  (0x0)  (int)
   pci.device_subclass = 128  (0x80)  (int)
   pci.linux.sysfs_path = 
'/sys/devices/pci0000:00/0000:00:10.0/0000:04:08.0'  (string)
   pci.product = 'SAA7133/SAA7135 Video Broadcast Decoder'  (string)
   pci.product_id = 28979  (0x7133)  (int)
   pci.subsys_product_id = 26224  (0x6670)  (int)
   pci.subsys_vendor = 'LeadTek Research Inc.'  (string)
   pci.subsys_vendor_id = 4221  (0x107d)  (int)
   pci.vendor = 'Philips Semiconductors'  (string)
   pci.vendor_id = 4401  (0x1131)  (int)

And running dmesg produced

saa7133[0]: found at 0000:04:08.0, rev: 16, irq: 19, latency: 64, mmio: 
0xfeaff800
saa7133[0]: subsystem: 107d:6670, board: UNKNOWN/GENERIC 
[card=0,autodetected]
saa7133[0]: board init: gpio is a022000
saa7133[0]: i2c eeprom 00: 7d 10 70 66 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7133[0]: i2c eeprom 10: 00 ff 82 0e ff 20 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 02 ff 01 04 08 ff 00 a8 ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff 18 00 c2 86 00 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0

I installed this card as if it were the kworld 110 and it works great.  I 
added
"   alias char-major-81 videodev
     alias char-major-81-0 saa7134
     options saa7134 card=90 "
to modprobe.conf and downloaded the nxt2004 firmware.


I don't have cable and I passed on trying to 
get the remote to work.  I also didn't try very 
hard to get the analog tuner to work.  I hope this info helps.