[linux-dvb] DViCO FusionHDTV DVB-T Dual Digital card - fail to load firmware

Craig Cook cncook001 at yahoo.com
Sat Jun 2 03:00:11 CEST 2007


May 2006 I went through pain to make this card work.  I did get it working under FC4.  Now it is time to upgrade.

Chose ubuntu 7.04 this time (installed a bigger disk in same box so I know everything works).  FC4 is still available until I can make this new version work.

===
from lspci -vvv
=====
02:01.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
        Subsystem: DViCO Corporation FusionHDTV DVB-T Dual Digital
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 21
        Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:01.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
        Subsystem: DViCO Corporation Unknown device db50
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 32 bytes
        Interrupt: pin A routed to IRQ 21
        Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        Capabilities: [4c] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
=====
I have manually added 
cx88_dvb
to /etc/modules

 uname -a
Linux myth 2.6.20-16-generic #2 SMP Wed May 23 01:46:23 UTC 2007 i686 GNU/Linux

partial dmesg output:

[   31.372109] dvb-usb: found a 'DViCO FusionHDTV DVB-T Dual USB' in cold state, will try to load a firmware
[   31.381966] cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
[   31.382100] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44,autodetected]
[   31.382106] TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
[   31.432095] cx2388x v4l2 driver version 0.0.6 loaded
[   31.575744] usb 4-4: USB disconnect, address 3
[   31.615455] parport: PnPBIOS parport detected.
[   31.615488] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[   32.023840] dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
[   32.023850] dvb-usb: could not stop the USB controller CPU.
[   32.023856] dvb-usb: error while transferring firmware (transferred size: -19, block size: 10)
[   32.023860] dvb-usb: firmware download failed at 15 with -22
[   32.023881] dvb_usb_cxusb: probe of 4-4:1.0 failed with error -22
[   32.151047] usbcore: registered new interface driver dvb_usb_cxusb
[   32.554524] cx88[0]/2: cx2388x 8802 Driver Manager
[   32.554559] ACPI: PCI Interrupt 0000:02:01.2[A] -> GSI 22 (level, low) -> IRQ 21
[   32.554575] cx88[0]/2: found at 0000:02:01.2, rev: 5, irq: 21, latency: 64, mmio: 0xfd000000
[   32.554766] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 22 (level, low) -> IRQ 21
[   32.554780] cx88[0]/0: found at 0000:02:01.0, rev: 5, irq: 21, latency: 64, mmio: 0xfc000000
[   32.554902] cx88[0]/0: registered device video0 [v4l2]
[   32.554948] cx88[0]/0: registered device vbi0
[   32.555767] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
[   32.555816] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   32.822194] usb 4-4: new high speed USB device using ehci_hcd and address 4
[   32.870123] intel8x0_measure_ac97_clock: measured 54105 usecs
[   32.870127] intel8x0: clocking to 48000
[   32.954554] usb 4-4: configuration #1 chosen from 1 choice
[   33.071330] usbtest 4-4:1.0: FX2 device
[   33.071337] usbtest 4-4:1.0: high speed {control bulk-in bulk-out} tests (+alt)
[   33.071350] usbcore: registered new interface driver usbtest
[   33.188448] fuse init (API version 7.8)
[   33.223451] lp0: using parport0 (interrupt-driven).
[   33.302665] cx2388x dvb driver version 0.0.6 loaded
[   33.302673] cx8802_register_driver() ->registering driver type=dvb access=shared
[   33.302679] CORE cx88[0]: subsystem: 18ac:db50, board: DViCO FusionHDTV DVB-T Dual Digital [card=44]
[   33.302685] cx88[0]/2: cx2388x based dvb card
[   33.353012] DVB: registering new adapter (cx88[0]).
[   33.353022] DVB: registering frontend 0 (Zarlink MT352 DVB-T)...

=======
# ls -R /dev/dvb
/dev/dvb:
adapter0

/dev/dvb/adapter0:
demux0  dvr0  frontend0  net0


USB cable is attached to the card as required.  Mythtv is operational and I can watch TV.  I do not have a second tuner and my remote does not work.

Any ideas?

Thanks

Craig




      ____________________________________________________________________________________
Shape Yahoo! in your own image.  Join our Network Research Panel today!   http://surveylink.yahoo.com/gmrs/yahoo_panel_invite.asp?a=7 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20070601/a06c6693/attachment.htm 


More information about the linux-dvb mailing list