[linux-dvb] [Fwd: Re: New Hauppauge Board]

Will Tatam will at netmindz.org.uk
Fri Mar 2 10:55:02 CET 2007


I sent the following email to the email address recommended for adding
support for new boards using the connexant chipset, but have had no
reply, so I'm sending to the list

Will

-------- Original Message --------
Subject: Re: New Hauppauge Board
Date: Sat, 24 Feb 2007 14:44:56 -0000 (UTC)
From: will at netmindz.co.uk
To: gunther.mayer at gmx.net
References: <36394.10.0.10.2.1172324031.squirrel at secure.netmindz.net>

p.s I've just tried building the latest copy of hg and setting the card=18
(the value i think it detected the similar DVB-T card as) but still no
joy, see the enclosed dmesg attachment

Will

> I think most of the info you need is on the website
>
> http://www.hauppauge.co.uk/pages/products/data_hvr4000.html
>
> The card was is very similar to the Nova-T PCI (connexant) that i had
> previously in thie machine, but this card isn't found by modprobe cx88-dvb
> The main chip had the same starting number for the chip (CX23882-19), but
> the last bit CX23882-?? was different. It's a bit of a pain to get the
> card back out so sorry for not giving the full details
>
> The following output was under 2.6.19-1.2288.fc5 but I can't see any
> mention of the details of this card user the hg version of CARDLIST.cx88
>
> # lspci
> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge
> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
> Controller (rev 80)
> 00:0f.0 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81)
> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81)
> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81)
> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81)
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
> [KT600/K8T800/K8T890 South]
> 00:11.5 Multimedia audio controller: VIA Technologies, Inc.
> VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
> 78)
> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and
> Audio Decoder (rev 05)
> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [Audio Port] (rev 05)
> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [MPEG Port] (rev 05)
> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [IR Port] (rev 05)
> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro
> VGA Adapter (rev 02)
>
> lspci -vn
> 00:00.0 0600: 1106:0259
>         Subsystem: 1106:aa01
>         Flags: bus master, 66MHz, medium devsel, latency 8
>         Memory at d8000000 (32-bit, prefetchable) [size=128M]
>         Capabilities: [80] AGP version 3.5
>         Capabilities: [50] Power Management version 2
>
> 00:00.1 0600: 1106:1259
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.2 0600: 1106:2259
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.3 0600: 1106:3259
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.4 0600: 1106:4259
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.7 0600: 1106:7259
>         Flags: bus master, medium devsel, latency 0
>
> 00:01.0 0604: 1106:b198
>         Flags: bus master, 66MHz, medium devsel, latency 0
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>         Memory behind bridge: e4000000-e5ffffff
>         Prefetchable memory behind bridge: e0000000-e3ffffff
>         Capabilities: [70] Power Management version 2
>
> 00:0d.0 0c00: 1106:3044 (rev 80) (prog-if 10)
>         Subsystem: 1106:3044
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at ea002000 (32-bit, non-prefetchable) [size=2K]
>         I/O ports at c000 [size=128]
>         Capabilities: [50] Power Management version 2
>
> 00:0f.0 0101: 1106:0571 (rev 06) (prog-if 8a)
>         Subsystem: 1106:aa01
>         Flags: bus master, medium devsel, latency 32
>         I/O ports at c400 [size=16]
>         Capabilities: [c0] Power Management version 2
>
> 00:10.0 0c03: 1106:3038 (rev 81)
>         Subsystem: 1106:aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at c800 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.1 0c03: 1106:3038 (rev 81)
>         Subsystem: 1106:aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at cc00 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.2 0c03: 1106:3038 (rev 81)
>         Subsystem: 1106:aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         I/O ports at d000 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.3 0c03: 1106:3038 (rev 81)
>         Subsystem: 1106:aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         I/O ports at d400 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:11.0 0601: 1106:3227
>         Subsystem: 1106:aa01
>         Flags: bus master, stepping, medium devsel, latency 0
>         Capabilities: [c0] Power Management version 2
>
> 00:11.5 0401: 1106:3059 (rev 60)
>         Subsystem: 1106:aa01
>         Flags: medium devsel, IRQ 7
>         I/O ports at d800 [size=256]
>         Capabilities: [c0] Power Management version 2
>
> 00:12.0 0200: 1106:3065 (rev 78)
>         Subsystem: 1106:0102
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at e000 [size=256]
>         Memory at ea001000 (32-bit, non-prefetchable) [size=256]
>         Capabilities: [40] Power Management version 2
>
> 00:14.0 0400: 14f1:8800 (rev 05)
>         Subsystem: 0070:6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e6000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>
> 00:14.1 0480: 14f1:8811 (rev 05)
>         Subsystem: 0070:6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e7000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 00:14.2 0480: 14f1:8802 (rev 05)
>         Subsystem: 0070:6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 00:14.4 0480: 14f1:8804 (rev 05)
>         Subsystem: 0070:6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 01:00.0 0300: 1106:3118 (rev 02)
>         Subsystem: 1106:3118
>         Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
>         Memory at e0000000 (32-bit, prefetchable) [size=64M]
>         Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
>         [virtual] Expansion ROM at e5000000 [disabled] [size=64K]
>         Capabilities: [60] Power Management version 2
>         Capabilities: [70] AGP version 3.0
>
> # lspci -v
> 00:00.0 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, 66MHz, medium devsel, latency 8
>         Memory at d8000000 (32-bit, prefetchable) [size=128M]
>         Capabilities: [80] AGP version 3.5
>         Capabilities: [50] Power Management version 2
>
> 00:00.1 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.2 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.3 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.4 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Flags: bus master, medium devsel, latency 0
>
> 00:00.7 Host bridge: VIA Technologies, Inc. CN400/PM880 Host Bridge
>         Flags: bus master, medium devsel, latency 0
>
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00
> [Normal decode])
>         Flags: bus master, 66MHz, medium devsel, latency 0
>         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>         Memory behind bridge: e4000000-e5ffffff
>         Prefetchable memory behind bridge: e0000000-e3ffffff
>         Capabilities: [70] Power Management version 2
>
> 00:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
> Controller (rev 80) (prog-if 10 [OHCI])
>         Subsystem: VIA Technologies, Inc. IEEE 1394 Host Controller
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at ea002000 (32-bit, non-prefetchable) [size=2K]
>         I/O ports at c000 [size=128]
>         Capabilities: [50] Power Management version 2
>
> 00:0f.0 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if
> 8a [Master SecP PriP])
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, medium devsel, latency 32
>         I/O ports at c400 [size=16]
>         Capabilities: [c0] Power Management version 2
>
> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81) (prog-if 00 [UHCI])
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at c800 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81) (prog-if 00 [UHCI])
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at cc00 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81) (prog-if 00 [UHCI])
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         I/O ports at d000 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 81) (prog-if 00 [UHCI])
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         I/O ports at d400 [size=32]
>         Capabilities: [80] Power Management version 2
>
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
> [KT600/K8T800/K8T890 South]
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: bus master, stepping, medium devsel, latency 0
>         Capabilities: [c0] Power Management version 2
>
> 00:11.5 Multimedia audio controller: VIA Technologies, Inc.
> VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
>         Subsystem: VIA Technologies, Inc. Unknown device aa01
>         Flags: medium devsel, IRQ 7
>         I/O ports at d800 [size=256]
>         Capabilities: [c0] Power Management version 2
>
> 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
> 78)
>         Subsystem: VIA Technologies, Inc. VT6102 [Rhine II] Embeded
> Ethernet Controller on VT8235
>         Flags: bus master, medium devsel, latency 32, IRQ 11
>         I/O ports at e000 [size=256]
>         Memory at ea001000 (32-bit, non-prefetchable) [size=256]
>         Capabilities: [40] Power Management version 2
>
> 00:14.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and
> Audio Decoder (rev 05)
>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e6000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [44] Vital Product Data
>         Capabilities: [4c] Power Management version 2
>
> 00:14.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [Audio Port] (rev 05)
>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e7000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 00:14.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [MPEG Port] (rev 05)
>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e8000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 00:14.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio
> Decoder [IR Port] (rev 05)
>         Subsystem: Hauppauge computer works Inc. Unknown device 6902
>         Flags: bus master, medium devsel, latency 32, IRQ 10
>         Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
>         Capabilities: [4c] Power Management version 2
>
> 01:00.0 VGA compatible controller: VIA Technologies, Inc. S3 Unichrome Pro
> VGA Adapter (rev 02) (prog-if 00 [VGA])
>         Subsystem: VIA Technologies, Inc. S3 Unichrome Pro VGA Adapter
>         Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 11
>         Memory at e0000000 (32-bit, prefetchable) [size=64M]
>         Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
>         [virtual] Expansion ROM at e5000000 [disabled] [size=64K]
>         Capabilities: [60] Power Management version 2
>         Capabilities: [70] AGP version 3.0
>
>
>
>
>

-------------- next part --------------
Linux version 2.6.19-1.2288.fc5 (brewbuilder at hs20-bc2-2.build.redhat.com) (gcc version 4.1.1 20070105 (Red Hat 4.1.1-51)) #1 Sat Feb 10 14:27:07 EST 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001bff0000 (usable)
 BIOS-e820: 000000001bff0000 - 000000001bff3000 (ACPI NVS)
 BIOS-e820: 000000001bff3000 - 000000001c000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 114672) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   114672
  HighMem    114672 ->   114672
early_node_map[1] active PFN ranges
    0:        0 ->   114672
On node 0 totalpages: 114672
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 863 pages used for memmap
  Normal zone: 109713 pages, LIFO batch:31
  HighMem zone: 0 pages used for memmap
DMI not present or invalid.
Using APIC driver default
ACPI: RSDP (v000 CN400                                 ) @ 0x000f6aa0
ACPI: RSDT (v001 CN400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3000
ACPI: FADT (v001 CN400  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1bff3040
ACPI: DSDT (v001 CN400  AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: Disabling ACPI support
Allocating PCI resources starting at 20000000 (gap: 1c000000:e3ff0000)
Detected 1333.397 MHz processor.
Built 1 zonelists.  Total pages: 113777
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
No local APIC present or hardware disabled
mapped APIC to ffffd000 (0139c000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c076c000 soft=c076b000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 448460k/458688k available (2083k kernel code, 9600k reserved, 807k data, 228k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff9a000 - 0xfffff000   ( 404 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xdc800000 - 0xff7fe000   ( 559 MB)
    lowmem  : 0xc0000000 - 0xdbff0000   ( 447 MB)
      .init : 0xc072d000 - 0xc0766000   ( 228 kB)
      .data : 0xc0608c72 - 0xc06d2af4   ( 807 kB)
      .text : 0xc0400000 - 0xc0608c72   (2083 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2668.74 BogoMIPS (lpj=1334373)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0381b83f 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 0381b13f 00000000 00000000 00000000 00000000 000000dd 00000000
CPU: Centaur VIA Nehemiah stepping 08
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1542k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfad70, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Using IRQ router VIA [1106/3227] at 0000:00:11.0
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e4000000-e5ffffff
  PREFETCH window: e0000000-e3ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
audit: initializing netlink socket (disabled)
audit(1172327905.858:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 38BFE5B32FEF5C5
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Bypassing VIA 8237 APIC De-Assert Message
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
agpgart: AGP aperture is 128M @ 0xd8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.0
    ide0: BM-DMA at 0xc400-0xc407, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xc408-0xc40f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: SAMSUNG SP1604N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY DVD RW DRU-510A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2
ide-floppy driver 0.99.newide
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 228k freed
Write protecting the kernel read-only data: 391k
input: AT Translated Set 2 keyboard as /class/input/input0
logips2pp: Detected unknown logitech mouse model 1
input: PS/2 Logitech Mouse as /class/input/input1
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel at redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
audit(1172327910.452:2): selinux=0 auid=4294967295
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Linux video capture interface: v2.00
input: PC Speaker as /class/input/input2
via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:12.0
PCI: Sharing IRQ 11 with 0000:00:10.0
PCI: Sharing IRQ 11 with 0000:00:10.1
eth0: VIA Rhine II at 0xea001000, 00:40:63:e5:09:2d, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T [card=18,insmod option]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
cx2388x v4l2 driver version 0.0.6 loaded
tveeprom 1-0050: Hauppauge model 69009, rev B2A0, serial# 1243050
tveeprom 1-0050: MAC address is 00-0D-FE-12-F7-AA
tveeprom 1-0050: tuner model is Philips FMD1216ME (idx 100, type 63)
tveeprom 1-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
tveeprom 1-0050: audio processor is CX882 (idx 33)
tveeprom 1-0050: decoder processor is CX882 (idx 25)
tveeprom 1-0050: has radio, has IR receiver, has no IR transmitter
cx88[0]: warning: unknown hauppauge model #69009
cx88[0]: hauppauge eeprom: model=69009
input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input3
cx88[0]/2: cx2388x 8802 Driver Manager
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:00:14.4
cx88[0]/2: found at 0000:00:14.2, rev: 5, irq: 10, latency: 32, mmio: 0xe8000000
PCI: Found IRQ 10 for device 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:14.4
cx88[0]/0: found at 0000:00:14.0, rev: 5, irq: 10, latency: 32, mmio: 0xe6000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
PCI: setting IRQ 7 as level-triggered
PCI: Found IRQ 7 for device 0000:00:11.5
PCI: Setting latency timer of device 0000:00:11.5 to 64
cx2388x alsa driver version 0.0.6 loaded
PCI: Found IRQ 10 for device 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:14.4
cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
USB Universal Host Controller Interface driver v3.0
PCI: Found IRQ 11 for device 0000:00:10.0
PCI: Sharing IRQ 11 with 0000:00:10.1
PCI: Sharing IRQ 11 with 0000:00:12.0
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000c800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:10.1
PCI: Sharing IRQ 11 with 0000:00:10.0
PCI: Sharing IRQ 11 with 0000:00:12.0
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:14.4
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:14.1
usb 1-1: new full speed USB device using uhci_hcd and address 2
PCI: Sharing IRQ 10 with 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:14.4
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
usb 1-1: configuration #1 chosen from 1 choice
PCI: Found IRQ 10 for device 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:10.2
PCI: Sharing IRQ 10 with 0000:00:10.3
PCI: Sharing IRQ 10 with 0000:00:14.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:00:14.2
PCI: Sharing IRQ 10 with 0000:00:14.4
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[ea002000-ea0027ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
input: CHESEN USB Keyboard as /class/input/input4
input: USB HID v1.10 Keyboard [CHESEN USB Keyboard] on usb-0000:00:10.0-2
input: CHESEN USB Keyboard as /class/input/input5
input: USB HID v1.10 Device [CHESEN USB Keyboard] on usb-0000:00:10.0-2
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0040635000071590]
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3242
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Floppy drive(s): fd0 is unknown type 15 (usb?), fd1 is unknown type 15 (usb?)
floppy0: no floppy controllers found
lp: driver loaded but no devices found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 917496k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1 across:917496k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
audit(1172327938.750:3): audit_pid=1692 old=0 by auid=4294967295
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
eth0: no IPv6 routers present
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
NFSD: starting 90-second grace period
cx2388x dvb driver version 0.0.6 loaded
cx8802_register_driver() ->registering driver type=dvb access=shared
CORE cx88[0]: subsystem: 0070:6902, board: Hauppauge Nova-T DVB-T [card=18]
cx88[0]/2: cx2388x based dvb card
cx22702_readreg: readreg error (ret == -121)
cx88[0]: frontend initialization failed
cx8802_dvb_probe dvb_register failed err = -1
cx8802_register_driver() ->probe failed err = -1
saa7146: register extension 'budget_ci dvb'.
[drm] Initialized drm 1.0.1 20051102
[drm] Initialized via 2.10.0 20060529 on minor 0
agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode



More information about the linux-dvb mailing list