[linux-dvb] DVICO NANO Australia

Eugene elubarsky at gmail.com
Mon Nov 12 10:58:25 CET 2007


I'm still having the same problem with my NANO2 as well. Managed to
use a workaround:

1. Removed the dvb_usb_cxusb module using rmmod
2. Connected the USB device into a VMWare instance running XP
3. The Windows driver seems to bootstrap the firmware..
4. Disconnected from vmware
5. did a 'modprobe dvb_usb_cxusb'
6. The device gets recognised as having a zl10353 ;)

I'm using 2.6.21.1 with the xc-bluebird.patch

-- Eugene

On Nov 8, 2007 3:31 PM, Collier Family <judithc at bigpond.net.au> wrote:
> Thanks for the fast response - yes it does work in windows.
>
>
>
> ----- Original Message -----
> From: "Michael Krufky" <mkrufky at linuxtv.org>
> To: "Collier Family" <judithc at bigpond.net.au>
> Cc: <linux-dvb at linuxtv.org>
> Sent: Thursday, November 08, 2007 2:58 PM
> Subject: Re: [linux-dvb] DVICO NANO Australia
>
>
> > Michael Krufky wrote:
> >> Collier Family wrote:
> >>> I have a  DVICO NANO but I am having the same troubles others had in
> >>> June. It appears it is not being recognised as being cold.
> >>>
> >>> I have followed the instructions at
> >>> http://fremnet.net/article/228/dvico-fusionhdtv-dual-digital-4-under-linux
> >>> and all went well except the frontend not set. dmesg follows
> >>>
> >>> usb 5-8: new high speed USB device using ehci_hcd and address 9
> >>> usb 5-8: configuration #1 chosen from 1 choice
> >>> dvb-usb: found a 'DViCO FusionHDTV DVB-T NANO2' in warm state.
> >>> dvb-usb: bulk message failed: -22 (2/0)
> >>> dvb-usb: will pass the complete MPEG2 transport stream to the software
> >>> demuxer.
> >>> DVB: registering new adapter (DViCO FusionHDTV DVB-T NANO2)
> >>> dvb-usb: bulk message failed: -110 (1/0)
> >>> dvb-usb: bulk message failed: -110 (3/0)
> >>> dvb-usb: bulk message failed: -110 (3/0)
> >>> dvb-usb: bulk message failed: -110 (5/0)
> >>> dvb-usb: no frontend was attached by 'DViCO FusionHDTV DVB-T NANO2'
> >>> dvb-usb: DViCO FusionHDTV DVB-T NANO2 successfully initialized and
> >>> connected.
> >>>
> >>> Is there any other information that may help I am running vanilla
> >>> 2.6.23.1 kernel on Scientific linux 5.0
> >>>
> >>> Thanks a lot for the work so far.
> >>
> >> The DVB-T NANO2 does not require the bluebird firmware -- the fx2 boots
> >> it from the eeprom.  So, the device does not have a "cold" state.  The
> >> only firmware that you need for it is the xc3028 firmware that was used
> >> in Markus' xc3028 kernel driver.
> >>
> >> However, there is alternate firmware required for the xc3028 for use in
> >> Australia.  I assume that you already have that.
> >
> > Sorry, I forgot to add the "helpful advice" ;-)
> >
> > ...It looks like the driver is having trouble accessing the zl10353.  Can
> > you check to make sure the device works in windows?
> >
> > -Mike
>
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>



More information about the linux-dvb mailing list