[linux-dvb] cx88-dvb: fix nxt200x rf input switching broke my tuner? :)

Nathan Faust nfaust at merchantwarehouse.com
Wed Sep 5 20:16:50 CEST 2007


-----Original Message-----
From: Michael Krufky [mailto:mkrufky at linuxtv.org] 
Sent: Wednesday, September 05, 2007 2:07 PM
To: Nathan Faust
Cc: CityK; linux-dvb at linuxtv.org
Subject: Re: [linux-dvb] cx88-dvb: fix nxt200x rf input switching broke
my tuner? :)

 > -----Original Message-----
 > From: CityK [mailto:CityK at rogers.com]
 > Sent: Wednesday, September 05, 2007 1:33 PM
 > To: Nathan Faust
 > Cc: linux-dvb at linuxtv.org
 > Subject: Re: [linux-dvb] cx88-dvb: fix nxt200x rf input switching
broke
 > my tuner? :)
 >
 > Nathan Faust wrote:
 >> Hi,
 >>
 >> I've notice the same thing with my Kworld ATSC-110.
 >> I'm running Ubuntu 7.10, 2.6.22-10-generic, x86_64.  I guess it is a
 >> change in the 2.6.22 kernel.
 >> Is there anyway to change this back so that QAM and NTSC inputs are
 >> the same?
 >>
 >
 > They should be the same now -- that was what the change was all
about.
 >
 > By default now, the top RF input should be 8VSB and the bottom should
be
 > QAM & analog (both ota and cable).

Nathan Faust wrote:
> CityK,
> 
> Thanks for your reply, but that is not what I'm seeing in MythTV and
> TVTime for /dev/video0.  I'm getting signal from /dev/video0 when I
use
> the upper input, not the lower one.  I haven't trying tuning 8VSB, but
> as for the QAM input, that seems to be working as expected.
> 
> Maybe I should look at the driver config for input select in SAA7134
or
> swap the input selection lines for VSB and QAM in the dvb code?
> 
> After looking at the input selection code in nxt200x.c, QAM and VSB,
it
> looks like if I switch these lines it will swap the inputs.
> 	//QAM
> -	state->config->set_pll_input(buf+1, 1); 
> +	state->config->set_pll_input(buf+1, 0);
> 
> 	//VSB
> -	state->config->set_pll_input(buf+1, 0);
> +	state->config->set_pll_input(buf+1, 1);
> 
> Am I correct?
> 
> I am confused as to what these lines do
> 	if (state->config->set_ts_params)
> 		state->config->set_ts_params(fe, 1);  <-- what the
> front-end parameter 0 or 1 mean.


Nathan,

Please do not top-quote....

As per your description above, you are correct... HOWEVER, now I
understand your 
issue -- you are running old code.

If you update to the latest v4l/dvb modules via linuxtv.org mercurial,
you will 
find that functionality has been restored as per your desire.

Please see http://linuxtv.org/repo

...for instructions to upgrade your v4l/dvb modules.

Good Luck,

Mike

------------------------

Mike,

I've been using the stock Ubuntu 7.10 kernel (2.6.22.4) with just the
Kworld ATSC-110 remote additions.
I'll give that a try and get back if I continue to have problems.

As for top quoting, sorry about that.

Thank you,
Nathan.




More information about the linux-dvb mailing list