[linux-dvb] [PATCH] Add initial support for DViCO FusionHDTV DVB-T Dual Express

[David Porter]

Hi

I have one of these, saw Stevens post and thought i would give it a go.

I built from : http://linuxtv.org/hg/~stoth/v4l-dvb
All seemed to go well with no errors.

dmesg reads:

[   31.964424] CORE cx23885[0]: subsystem: 18ac:db78, board: DViCO 
FusionHDTV DVB-T Dual Express [card=11,autodetected]
[   32.104767] cx23885[0]: i2c bus 0 registered
[   32.104781] cx23885[0]: i2c bus 1 registered
[   32.104794] cx23885[0]: i2c bus 2 registered
[   32.164385] input: i2c IR (FusionHDTV) as /devices/virtual/input/input8
[   32.422764] ir-kbd-i2c: i2c IR (FusionHDTV) detected at i2c-1/1-006b/ir0 
[cx23885[0]]
[   32.423135] cx23885[0]: cx23885 based dvb card
[   32.492021] xc2028 1-0061: creating new instance
[   32.492027] xc2028 1-0061: type set to XCeive xc2028/xc3028 tuner
[   32.492036] DVB: registering new adapter (cx23885[0])
[   32.492040] DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
[   32.492386] cx23885[0]: cx23885 based dvb card
[   32.492924] xc2028 2-0061: creating new instance
[   32.492926] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
[   32.492928] DVB: registering new adapter (cx23885[0])
[   32.492930] DVB: registering frontend 1 (Zarlink ZL10353 DVB-T)...
[   32.493228] cx23885_dev_checkrevision() Hardware revision = 0xb0
[   32.493236] cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, 
latency: 0, mmio: 0xfe800000

But scanning, returns :

[ 1381.214624] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
[ 1382.220858] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
[ 1382.260825] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
[ 1383.267724] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.
[ 1383.276680] xc2028 1-0061: Error: firmware xc3028-v27.fw not found.

I checked  /lib/firmware/ but xc3028-v27.fw is not in the directory ?

Must have messed it up somewhere! Any help appreciated.

Thanks
David

----- Original Message ----- 
From: "Steven Toth" <stoth at linuxtv.org>
To: "Luke Yelavich" <themuso at themuso.com>
Cc: <linux-dvb at linuxtv.org>
Sent: Wednesday, August 06, 2008 11:44 AM
Subject: Re: [linux-dvb] [PATCH] Add initial support for DViCO FusionHDTV 
DVB-T Dual Express


>
>>>> I've tested with the HVR1500Q (xc5000 based) and I'm happy with the
>>>> results. Can you both try the DViCO board?
>>> It tests fine and I like how simpler things have got.
>>
>> I pulled the above linked tree, and compiled the modules. It seems at the 
>> moment for the dual express, that I have to pass the parameter card=11 to 
>> the driver, for it to correctly find the card and make use of all 
>> adapters. Without any module parameters, dmsg complains that the card 
>> couldn't be identified, yet two adapters are shown. I have two of these 
>> cards.
>>
>> Hope this helps some.
>
> .. And they're both the same model?
>
> If so, insert one at a time and run the 'lspci -vn' command, save the
> output for each card.
>
> Post the output here.
>
> Assuming you load the driver with card=11, does each card work correctly
> after that?
>
> - Steve
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>