[linux-dvb] DVICO FusionHDTV5 USB unable to find symbol lgdt330x_attach

David Shay david at shay.net
Thu Dec 18 07:32:45 CET 2008


On Thu, Dec 18, 2008 at 12:26 AM, David Shay <davideshay at gmail.com> wrote:

> I'm having a problem with the device listed above.
> Relevant facts:
>
> DVICO FusionHDTV5 USB device (USB device ID 0fe9:d501)
> Gentoo 2.6.26, running kernel gentoo-sources 2.6.26-r4 (dvb drivers
> initially from kernel only)
>
> The following is the dmesg log at bootup:
>
> dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in warm state.
> i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] registered
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (DViCO FusionHDTV5 USB Gold)
> DVB: Unable to find symbol lgdt330x_attach()
> dvb-usb: no frontend was attached by 'DViCO FusionHDTV5 USB Gold'
> input: IR-receiver inside an USB DVB receiver as /class/input/input5
> dvb-usb: schedule remote query interval to 100 msecs.
> dvb-usb: DViCO FusionHDTV5 USB Gold successfully initialized and connected.
> usbcore: registered new interface driver dvb_usb_cxusb
>
> Main error here is the unable to find symbol lgdt330x_attach() line. Not
> sure what is happening here. Was on #linuxtv last night and on a hunch, we
> disconnected the device, manually modprobe'd lgdt330x and reconnected, and
> all was fine.  Recommendation was to install from the latest drivers from
> mercurial, which I have done.  I still get the same symptoms as indicated
> above.  If I then disconnect and reconnect (even without the modprobe), I
> get the rest of the log, as indicated below, which makes everything
> successful:
>
>
I was wrong about this and obviously didn't read very well after midnight.
 I *DID INDEED* have to manually modprobe to get further.  However, now I
get a new error:

i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] unregistered
dvb-usb: DViCO FusionHDTV5 USB Gold successfully deinitialized and
disconnected.

usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in cold state, will try to
load a
firmware
firmware: requesting dvb-usb-bluebird-01.fw
dvb-usb: downloading firmware from file 'dvb-usb-bluebird-01.fw'
usb 1-4: USB disconnect, address 6
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 1-4: new high speed USB device using ehci_hcd and address 7
usb 1-4: configuration #1 chosen from 1 choice
dvb-usb: found a 'DViCO FusionHDTV5 USB Gold' in warm state.
i2c-adapter i2c-1: adapter [DViCO FusionHDTV5 USB Gold] registered
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (DViCO FusionHDTV5 USB Gold)
i2c-adapter i2c-1: master_xfer[0] W, addr=0x0e, len=1
i2c-adapter i2c-1: master_xfer[1] R, addr=0x0e, len=1
DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM
Frontend)
...
DVB: Unable to find symbol simple_tuner_attach()
input: IR-receiver inside an USB DVB receiver as /class/input/input7
dvb-usb: schedule remote query interval to 100 msecs.
dvb-usb: DViCO FusionHDTV5 USB Gold successfully initialized and connected.

Note that now I get the error about "simple_tuner_attach". Argh.

>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20081218/2bee01df/attachment.htm 


More information about the linux-dvb mailing list