[linux-dvb] Yuan EC372S (STK7700D based device)
Albert Comerma
albert.comerma at gmail.com
Tue Feb 19 00:30:29 CET 2008
It seems ok. Could you test a scan with kaffeine instead of looking for a
specific location? And if you do so it reports signal strenght?
By the way, what does it mean moi and moikka? Hello in finish?
Albert
2008/2/18, Antti Palosaari <crope at iki.fi>:
>
> latest v4l-master + patch you give.
>
>
> regards
> Antti
>
> Albert Comerma wrote:
>
> > Uhm... that's strange, I don't have any of this cards to test, but other
> > people reported that this solution was working. Could you post the
> > dib0700_devices.c you're using to have a look?
> >
> > Albert
> >
>
> > 2008/2/18, Antti Palosaari <crope at iki.fi <mailto:crope at iki.fi>>:
>
> >
> > moi
> > It does not work for me. It says same PID-filter timeout as I have
> got
> > earlier. I don't have amplified antenna now, but I can say that all
> > other DVB-T sticks I have are working with this small antenna. It
> could
> > be that sensitivity of this hardware is bad or there is something
> wrong
> > with driver or firmware. Lets try to test it Windows to see if it is
> > working or not.
> > Logs attached.
> >
> >
> > regards
> > Antti
> >
> > Albert Comerma wrote:
> >
> > > Hey people, we already solved this problems. I submitted a patch
> > a few
> > > days ago, but I think it's not on the current sources. I send
> > again the
> > > patch. Basically it must use the same frontend description as
> > asus cards.
> > >
> > > Albert
> > >
> >
> > > 2008/2/18, Antti Palosaari <crope at iki.fi <mailto:crope at iki.fi>
>
> > <mailto:crope at iki.fi <mailto:crope at iki.fi>>>:
>
> >
> > >
> > > moikka
> > > I have also this device (express card). I haven't looked
> > inside yet, but
> > > I think there is DibCOM STK7700D (in my understanding dual
> > demod chip)
> > > and only *one* MT2266 tuner. I tried various GPIO settings
> but no
> > > luck yet.
> > > GPIO6 is for MT2266.
> > > GPIO9 and GPIO10 are for frontend.
> > >
> > > Looks like tuner goes to correct frequency because I got
> always
> > > PID-filter timeouts when tuning to correct freq. I will now
> > try to take
> > > some usb-sniffs to see configuration used. Any help is
> welcome.
> > >
> > > regards
> > > Antti
> > >
> > > Albert Comerma wrote:
> > > > Hi!, with Michel (mm-sl at ibelgique.com
> > <mailto:mm-sl at ibelgique.com>
> >
> > > <mailto:mm-sl at ibelgique.com <mailto:mm-sl at ibelgique.com>>
> > <mailto:mm-sl at ibelgique.com <mailto:mm-sl at ibelgique.com>
> >
>
> > > <mailto:mm-sl at ibelgique.com <mailto:mm-sl at ibelgique.com>>>)
> who
>
> > >
> > > > is a owner of this Yuan card we added the device to
> > > dib0700_devices, and
> > > > we got it recognized without problems. The only problem is
> > that no
> > > > channel is detected on scan on kaffeine or other
> software... I
> > > post some
> > > > dmesg. We don't know where it may be the problem... or how
> to
> > > detect it...
> > > >
> > > > usb 4-2: new high speed USB device using ehci_hcd and
> > address 6
> > > > usb 4-2: new device found, idVendor=1164, idProduct=1edc
> > > > usb 4-2: new device strings: Mfr=1, Product=2,
> SerialNumber=3
> > > > usb 4-2: Product: STK7700D
> > > > usb 4-2: Manufacturer: YUANRD
> > > > usb 4-2: SerialNumber: 0000000001
> > > > usb 4-2: configuration #1 chosen from 1 choice
> > > > dvb-usb: found a 'Yuan EC372S' in cold state, will try to
> > load a
> > > firmware
> > > > dvb-usb: downloading firmware from file
> > 'dvb-usb-dib0700-1.10.fw'
> > > > dib0700: firmware started successfully.
> > > > dvb-usb: found a 'Yuan EC372S' in warm state.
> > > > dvb-usb: will pass the complete MPEG2 transport stream to
> the
> > > software
> > > > demuxer.
> > > > DVB: registering new adapter (Yuan EC372S)
> > > > dvb-usb: no frontend was attached by 'Yuan EC372S'
> > > > dvb-usb: will pass the complete MPEG2 transport stream to
> the
> > > software
> > > > demuxer.
> > > > DVB: registering new adapter (Yuan EC372S)
> > > > DVB: registering frontend 1 (DiBcom 7000PC)...
> > > > MT2266: successfully identified
> > > > input: IR-receiver inside an USB DVB receiver as
> > /class/input/input10
> > > > dvb-usb: schedule remote query interval to 150 msecs.
> > > > dvb-usb: Yuan EC372S successfully initialized and
> connected.
> > > >
> > > >
> > >
> > > >
> > >
> >
> ------------------------------------------------------------------------
> > > >
> > > > _______________________________________________
> > > > linux-dvb mailing list
> >
> > > > linux-dvb at linuxtv.org <mailto:linux-dvb at linuxtv.org>
>
> > <mailto:linux-dvb at linuxtv.org <mailto:linux-dvb at linuxtv.org>>
>
> >
> > > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> > >
> > >
> > >
> > > --
> > > http://palosaari.fi/
> > >
> > >
> > >
> > >
> >
> ------------------------------------------------------------------------
> > >
> > > _______________________________________________
> > > linux-dvb mailing list
> > > linux-dvb at linuxtv.org <mailto:linux-dvb at linuxtv.org>
> > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
> >
> >
> > --
> > http://palosaari.fi/
> >
> >
>
> > Bus 001 Device 005: ID 1164:1edc YUAN High-Tech Development Co., Ltd
> > Device Descriptor:
> > bLength 18
> > bDescriptorType 1
> > bcdUSB 2.00
> > bDeviceClass 0 (Defined at Interface level)
> > bDeviceSubClass 0
> > bDeviceProtocol 0
> > bMaxPacketSize0 64
> > idVendor 0x1164 YUAN High-Tech Development Co., Ltd
> > idProduct 0x1edc
> > bcdDevice 1.00
> > iManufacturer 1 YUANRD
> > iProduct 2 STK7700D
> > iSerial 3 0000000001
> > bNumConfigurations 1
> > Configuration Descriptor:
> > bLength 9
> > bDescriptorType 2
> > wTotalLength 46
> > bNumInterfaces 1
> > bConfigurationValue 1
> > iConfiguration 0
> > bmAttributes 0xa0
> > Remote Wakeup
> > MaxPower 500mA
> > Interface Descriptor:
> > bLength 9
> > bDescriptorType 4
> > bInterfaceNumber 0
> > bAlternateSetting 0
> > bNumEndpoints 4
> > bInterfaceClass 255 Vendor Specific Class
> > bInterfaceSubClass 0
> > bInterfaceProtocol 0
> > iInterface 0
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x01 EP 1 OUT
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x81 EP 1 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x82 EP 2 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Endpoint Descriptor:
> > bLength 7
> > bDescriptorType 5
> > bEndpointAddress 0x83 EP 3 IN
> > bmAttributes 2
> > Transfer Type Bulk
> > Synch Type None
> > Usage Type Data
> > wMaxPacketSize 0x0200 1x 512 bytes
> > bInterval 1
> > Device Qualifier (for other device speed):
> > bLength 10
> > bDescriptorType 6
> > bcdUSB 2.00
> > bDeviceClass 0 (Defined at Interface level)
> > bDeviceSubClass 0
> > bDeviceProtocol 0
> > bMaxPacketSize0 64
> > bNumConfigurations 1
> >
> > Feb 18 23:50:53 localhost kernel: usb 1-8: USB disconnect, address 5
> > Feb 18 23:50:55 localhost kernel: usb 1-8: new high speed USB device
> > using ehci_hcd and address 6
> > Feb 18 23:50:55 localhost kernel: usb 1-8: configuration #1 chosen
> > from 1 choice
> > Feb 18 23:50:55 localhost kernel: dib0700: loaded with support for 6
> > different device-types
> > Feb 18 23:50:55 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> > cold state, will try to load a firmware
> > Feb 18 23:50:55 localhost kernel: dvb-usb: downloading firmware from
> > file 'dvb-usb-dib0700-1.10.fw'
> > Feb 18 23:50:55 localhost kernel: dib0700: firmware started
> > successfully.
> > Feb 18 23:50:56 localhost kernel: dvb-usb: found a 'Yuan EC372S' in
> > warm state.
> > Feb 18 23:50:56 localhost kernel: dvb-usb: will pass the complete
> > MPEG2 transport stream to the software demuxer.
> > Feb 18 23:50:56 localhost kernel: DVB: registering new adapter (Yuan
> > EC372S)
> > Feb 18 23:50:56 localhost kernel: DVB: registering frontend 0
> > (DiBcom 7000PC)...
> > Feb 18 23:50:56 localhost kernel: MT2266: successfully identified
> > Feb 18 23:50:56 localhost kernel: dvb-usb: Yuan EC372S successfully
> > initialized and connected.
> > Feb 18 23:50:56 localhost kernel: usbcore: registered new interface
> > driver dvb_usb_dib0700
> >
> > [crope at localhost linuxtv]$ scandvb fi-Oulu
> > scanning fi-Oulu
> > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> > initial transponder 634000000 0 2 9 3 1 2 0
> > initial transponder 714000000 0 2 9 3 1 2 0
> > initial transponder 738000000 0 2 9 3 1 2 0
> > initial transponder 602000000 0 2 9 3 1 2 0
> > >>> tune to:
> >
> 634000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 714000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 738000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > >>> tune to:
> >
> 602000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_8:HIERARCHY_NONE
> > WARNING: filter timeout pid 0x0011
> > WARNING: filter timeout pid 0x0000
> > WARNING: filter timeout pid 0x0010
> > dumping lists (0 services)
> > Done.
> > [crope at localhost linuxtv]$
> >
> >
> >
> >
> > ------------------------------------------------------------------------
> >
> > _______________________________________________
> > linux-dvb mailing list
> > linux-dvb at linuxtv.org
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
>
> --
> http://palosaari.fi/
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20080219/8e3cc215/attachment-0001.htm
More information about the linux-dvb
mailing list