[linux-dvb] SkyStar2 Rev. 2.7V / ITD1000

Thomas Debe sert_delta at gmx.de
Wed Jan 9 15:11:01 CET 2008


Hello !
I bought  such a SkyStar2  2.7V .

$ lspci -vnn

05:01.0 Network controller [Class 0280]: Techsan Electronics Co Ltd B2C2 
FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 02)
        Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / 
Technisat SkyStar2 DVB card [13d0:2103]
        Flags: bus master, slow devsel, latency 32, IRQ 18
        Memory at f9100000 (32-bit, non-prefetchable) [size=64K]
        I/O ports at c100 [size=32]

This card has FlexCopII DVB chip, a  PN1010 and an ITD1000.

I used   v4l-dvb-skystar2-rev27.

Fortress:~ # ls -l /dev/dvb/adapter0/
total 0
crw-rw----+ 1 root video 212, 4 Dec 29 13:51 demux0
crw-rw----+ 1 root video 212, 5 Dec 29 13:51 dvr0
crw-rw----+ 1 root video 212, 3 Dec 29 13:51 frontend0
crw-rw----+ 1 root video 212, 7 Dec 29 13:51 net0

But I can not tune or do anything else.

dmesg:
..
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 19 (level, low) -> IRQ 18
DVB: registering new adapter (FlexCop Digital TV device)
rd(53): f8 00 d0 d7 13 ad 98 00 21
b2c2-flexcop: MAC address = 00:d0:d7:13:ad:98
rd(53): 00 03
wr(08): 20
b2c2-flexcop: ISL6421 successfully attached
wr(53): 02 01
rd(61): 00 00
ITD1000: id: 0
ITD1000: successfully identified
b2c2-flexcop: ITD1000 successfully attached
b2c2-flexcop: found 'Samsung S5H1420/PnpNetwork PN1010 DVB-S' .
DVB: registering frontend 0 (Samsung S5H1420/PnpNetwork PN1010 DVB-S)...
b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S rev 2.7a/u' at 
the 'PCI' bus controlled by a 'FlexCopIIb' complete
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
..
Fortress:~ # 
dvbscan /usr/share/dvb/scan/dvb-s/Astra-19.2E /root/.szap/channels.conf
scanning /usr/share/dvb/scan/dvb-s/Astra-19.2E
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
initial transponder 12551500 V 22000000 5
>>> tune to: 12551:v:0:22000
WARNING: >>> tuning failed!!!
>>> tune to: 12551:v:0:22000 (tuning failed)
WARNING: >>> tuning failed!!!
ERROR: initial tuning failed
dumping lists (0 services)
Done.

Is there Documentation available (ITD 1000) to get this driver and the card to 
work ?

with best regards

Thomas Debe



More information about the linux-dvb mailing list