[linux-dvb] Pinnacle PCTV Dual DVB-T Diversity Stick built in IR-Receiver supported ?

SUBHRANIL CHOUDHURY subhra85 at gmail.com
Sun Jul 13 14:09:58 CEST 2008


hi,

I am working on DVB-T for the first time. I am using a Pinnacle PCTV 2001e
USB DVB-T dongle.In that the device dri vers are getting registered and the
device is getting detected.I am using a 2.6.23.15 kernel.

The dmesg is as follows:

dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully deinitialized
and disconnected.
usb 1-1.4: new high speed USB device using musb_hdrc and address 4
usb 1-1.4: Product: PCTV 2001e
usb 1-1.4: Manufacturer: PINNACLE
usb 1-1.4: SerialNumber: 12020607
usb 1-1.4: configuration #1 chosen from 1 choice
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in cold state,
will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 0 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: will pass the complete MPEG2 transport stream to the software
demuxer.
DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
DVB: registering frontend 1 (DiBcom 7000PC)...
DiB0070: successfully identified
dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully initialized
and connected.

But, after that when i am trying to run any scan application , it is showing
"scan failed".

the dmesg after running scan application is,

APPLN INFO >> Inside scan_network
APPLN INFO >> Inside tune_initial
Inside alloc_transponder
initial transponder 474166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 498166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 522166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 538166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 562166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 586166000 0 3 9 3 1 2 0
Inside alloc_transponder
initial transponder 714166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 738166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 754166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 762166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 786166000 0 2 9 3 1 0 0
Inside alloc_transponder
initial transponder 810166000 0 2 9 3 1 0 0
Inside tune_to_next_transponder()
Inside tune_to_transponder()
APPLN INFO >> Entered __tune_to_transponder()
>>> tune to:
474166000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
WARNING: >>> tuning failed!!!
APPLN INFO >> Entered __tune_to_transponder()
>>> tune to:
474166000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_2_3:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_1_32:HIERARCHY_NONE
(tuning failed)
WARNING: >>> tuning failed!!!
Inside tune_to_transponder()

etc, etc.

Can Anyone Please tell me if you have faced a similar problem or what is
happening ?
Do i have to add something to the kernel?

Best regards,
subhro
___________________________________________________________________________________________________________________
On Sat, Jul 12, 2008 at 11:36 PM, Ingo Arndt <scachi at gmx.de> wrote:

> Hello,
>
> as I haven't received any answer yet I'll post my question again,
>
> I have a Pinnacle PCTV Dual DVB-T Diversity Stick which works fine.
> The only thing I am missing is the built-in infrared receiver which is not
> recognized.
>
> Is anyone using this Pinnacle DVB-T stick and got it's remote control
> working ?
>
> Am I missing a module, a module option or something else
> or is the ir receiver just not supported by now ?
>
> I use the kernel 2.6.25 with tuxonice-patches on archlinux.
>
> lsusb output:
> ------------------------- lsusb output start ---
> idVendor           0x2304 Pinnacle Systems, Inc. [hex]
>  idProduct          0x0229
>  bcdDevice            0.01
>  iManufacturer           1 PINNACLE
>  iProduct                2 PCTV 2001e
>  iSerial                 3 12027630
> ------------------------- lsusb output stop ---
>
>
> mesg output:
> ---------------- dmesg code start ---
> usb 7-3: new high speed USB device using ehci_hcd and address 9
> usb 7-3: configuration #1 chosen from 1 choice
> dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in cold state,
> will try to load a firmware
> dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
> dib0700: firmware started successfully.
> dvb-usb: found a 'Pinnacle PCTV Dual DVB-T Diversity Stick' in warm state.
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
> DVB: registering frontend 0 (DiBcom 7000PC)...
> DiB0070: successfully identified
> dvb-usb: will pass the complete MPEG2 transport stream to the software
> demuxer.
> DVB: registering new adapter (Pinnacle PCTV Dual DVB-T Diversity Stick)
> DVB: registering frontend 1 (DiBcom 7000PC)...
> DiB0070: successfully identified
> dvb-usb: Pinnacle PCTV Dual DVB-T Diversity Stick successfully
> initialized and connected.
> ----------------- dmesg code end ---
>
>
> Best regards,
>  Ingo
>
> _______________________________________________
> linux-dvb mailing list
> linux-dvb at linuxtv.org
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.linuxtv.org/pipermail/linux-dvb/attachments/20080713/5c1221ab/attachment.htm 


More information about the linux-dvb mailing list