[linux-dvb] TechniSat CableStar HD2 & CAM

[Ludek]

Hi,

I've problem with TechniCrypt CAM inserted on my TechniSat CableStar HD2 
  (DVB-C card) with current mantis driver. I'm able to watch FTA 
channels only :-(  As I read this list I'm afraid that CAM modules with 
this card is not supported yet. Does anyone get this card with CAM working?

[ 4197.469043] Mantis 0000:05:00.0: PCI INT A -> GSI 20 (level, low) -> 
IRQ 20
[ 4197.469078] irq: 20, latency: 32
[ 4197.469079]  memory: 0xec100000, mmio: 0xffffc20004950000
[ 4197.469082] found a VP-2040 PCI DVB-C device on (05:00.0),
[ 4197.469084]     Mantis Rev 1 [1ae4:0002], irq: 20, latency: 32
[ 4197.469087]     memory: 0xec100000, mmio: 0xffffc20004950000
[ 4197.471385]         mantis_i2c_write: Address=[0x50] <W>[ 08 ]
[ 4197.471982]         mantis_i2c_read:  Address=[0x50] <R>[ 00 08 c9 d0 
1f 2c ]
[ 4197.474091]     MAC Address=[00:08:c9:d0:1f:2c]
[ 4197.474119] mantis_alloc_buffers (0): DMA=0x541a0000 
cpu=0xffff8800541a0000 size=65536
[ 4197.474190] mantis_alloc_buffers (0): RISC=0x34c0a000 
cpu=0xffff880034c0a000 size=1000
[ 4197.474256] DVB: registering new adapter (Mantis dvb adapter)
[ 4197.992116] mantis_frontend_init (0): Probing for CU1216 (DVB-C)
[ 4197.992176]         mantis_i2c_write: Address=[0x50] <W>[ ff ]
[ 4197.992528]         mantis_i2c_read:  Address=[0x50] <R>[ e4 ]
[ 4197.992956]         mantis_i2c_write: Address=[0x0c] <W>[ 1a ]
[ 4197.993308]         mantis_i2c_read:  Address=[0x0c] <R>[ 7d ]
[ 4197.993727]         mantis_i2c_write: Address=[0x50] <W>[ ff ]
[ 4197.994078]         mantis_i2c_read:  Address=[0x50] <R>[ e4 ]
[ 4197.994465]         mantis_i2c_write: Address=[0x0c] <W>[ 00 33 ]
[ 4197.995226]         mantis_i2c_write: Address=[0x0c] <W>[ 1a ]
[ 4197.995577]         mantis_i2c_read:  Address=[0x0c] <R>[ 7d ]
[ 4197.995928] TDA10023: i2c-addr = 0x0c, id = 0x7d
[ 4197.995931] mantis_frontend_init (0): found Philips CU1216 DVB-C 
frontend (TDA10023) @ 0x0c
[ 4197.995993] mantis_frontend_init (0): Mantis DVB-C Philips CU1216 
frontend attach success
[ 4197.996117] DVB: registering adapter 0 frontend 0 (Philips TDA10023 
DVB-C)...
[ 4197.996234] mantis_ca_init (0): Registering EN50221 device
[ 4197.996289] dvb_ca_en50221_init
[ 4197.996374] mantis_ca_init (0): Registered EN50221 device
[ 4197.996430] CAMCHANGE IRQ slot:0 change_type:1
[ 4197.996431] dvb_ca_en50221_thread_wakeup
[ 4197.996437] mantis_hif_init (0): Adapter(0) Initializing Mantis Host 
Interface
[ 4197.996674] dvb_ca_en50221_thread
[ 4199.000019] CAMREADY IRQ slot:0
[ 4199.000034] dvb_ca_en50221_thread_wakeup
[ 4199.000350] TUPLE type:0x0 length:0
[ 4199.000355] dvb_ca adapter 0: Invalid PC card inserted :(

Regards,

Ludek