[vdr] multiple non-independent frontends (was: Re: [ANNOUNCE] VDR developer version 1.7.11)

Oliver Endriss o.endriss at gmx.de
Wed Jan 6 16:52:18 CET 2010


Manu Abraham wrote:
> On Wed, Jan 6, 2010 at 5:55 PM, Klaus Schmidinger
> <Klaus.Schmidinger at tvdr.de> wrote:
> > On 06.01.2010 14:22, Tomasz Bubel wrote:
> >> [...]
> >>> - Added support for DVB cards with multiple fontends. Note that this only
> >>>  works for DVB cards where each frontend can be used independently of all
> >>>  the others on the same adapter.
> >> [...]
> >> Any chance of using using DVB-T frontend on HVR-4000? This card have 2
> >> separate frontends. And as quoted on
> >> http://www.linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-4000:
> >>
> >> "Multiple frontends are supported: DVB-S/S2 and DVB-T appear as
> >> /dev/dvb/adapterN/frontend0 and /dev/dvb/adapterN/frontend1
> >> respectively.
> >>
> >> Due to a hardware limitation, the two frontends cannot be used
> >> simultaneously. However they can be used sequentially within the same
> >> application. The driver handles the mutual exclusion appropriately."
> >
> > Well, that's still a problem.
> > Is there a defined way (via the LinuxDVB driver API) through which VDR
> > can find out whether the frontends can be used independently?
> 
> Some more food for thought ..
> 
> There is also one more added problem: Say there are two adapters and
> two frontends. I will try to convey the thought as simplest as
> possible by me...
> 
> A case in which frontend0 is bound to adapter0 and frontend1 is bound
> to adapter 1
> 
> This would seem like a classical case of having 2 independent
> adapters. But let's analyze it a bit more deeply. The two adapters A0
> and A1 are on the same physical A (adapter) chip and can send you data
> simultaneously on both the devices. Likewise F0 and F1 can be on the
> same physical F (frontend) chip and can send you simultaneous data to
> both A0 and A1.
> 
> Now suppose that you are having F0 and F1 operational: The F chip
> would have a limitation on some parameter, which is based on a
> combination of F0 and F1. If the sum parameter is exceeded on the
> whole F chip, the entire F chip would crash and might need a Reset.
> 
> Likewise the same holds good for the A chip too ..
> 
> Another case is where you have A0, A1 and F0, F1 on the same chip
> while additionally providing F2 and F3 on virtual A0' and A1'.
> 
> But in all cases, the question remains the same. How would the
> application like to handle a situation, when a certain parameter will
> be exceed on the next operation on the next 'Fx' interface ? (If the
> application feels free and does the operation which might cause some
> parameter to exceed, the chip as a whole would not respond, unless
> reset again)
> 
> Operations like this might be common on cards having dual, quad and
> hex frontends. The card itself might be able to stream dual, quad and
> hex simultaneous streams.

Imho limitations or dependencies between different *adapters* are not
acceptable. If a driver maps frontends to different adapters, the driver
pretends that they can be used independent of each other and without
limitations.

If there are limitations, the frontends must be assigned to the same
adapter. Anything else does not make any sense to me.

CU
Oliver

-- 
----------------------------------------------------------------
VDR Remote Plugin 0.4.0: http://www.escape-edv.de/endriss/vdr/
4 MByte Mod: http://www.escape-edv.de/endriss/dvb-mem-mod/
Full-TS Mod: http://www.escape-edv.de/endriss/dvb-full-ts-mod/
----------------------------------------------------------------



More information about the vdr mailing list