CVS log for dvb-kernel/build-2.6/insmod.sh

Up to [DVB] / dvb-kernel / build-2.6

Request diff between arbitrary revisions

Keyword substitution: kv
Default branch: MAIN

Add lgdt330x and nxt200x to insmod.sh

Signed-off-by: Michael Krufky <mkrufky@m1k.net>

adding special stv0297-driver for the Technisat/B2C2 CableStar2 PCI and USB
devices (USB untested)

This driver could also be used with other stv0297-based cards, but someone has
to do it.

The CableStar2's stv0297-driver is tested with QAM32/64/128/256 and has a very
nice reception-qualitiy.

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>

corrected nxt2002 module (un)load. sorry

(un)load the nxt6000-demod-module

Typo

Add s5h1420 to development script

added cxusb-stuff to Makefile and insmod.sh
correct debug-switch for the dib3000-frontends
added firmware_class load to the debug-part of insmod.sh

added support for the Broadcom BCM3510 ATSC (8VSB/16VSB & ITU J83 AnnexB FEC QAM64/256) demodulator used
in the first generation of Air2PC ATSC PCI-cards/USB-boxes made by B2C2.

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>

skystar2 has been dropped

fixed 'insmod.sh debug' for saa7146-based cards

corrected a typo in umt-010.c

Added a new driver for the µDigiTV USB2.0 DVB-T receiver made by Nebula Electronics. It isn't working yet, but with the help of Allan Third it will be very soon. Thanks.

- ported all dibusb drivers to fit into the dvb-usb-frameword
- created dvb-pll-entries for the tuner used with the dibusb-drivers
- removed all traces of the dibusb driver
- adapted the dib3000-frontends to get along with the dvb-pll-changes

 budget-av:
  - remove enable_ci, ci interface is assumed to be present if the saa7113
    is not found.
  - reduce the delay when checking for saa7113
  - clean up the cam reset according to specifications
  - turn off Vcc to the cam slot if cam is removed or fails reset
  - remove cam reset in ciintf_init
  - clean up printks (KERN_)
  - move gpio setting into saa7113_init
  - clean up unreadable frontend_init

- moved the flexcop-driver-suite to linux/drivers
- adapted build-2.6 (removed skystar2 from insmod.sh)
- corrected some bugs in Kconfig
- tried compilation with linux 2.6.11 (as module and as compiled-in-driver)

build and load dvb-pll

patch by Taylor Jacob to add support for ATSC/VSB frontends
and the B2C2/BBTI Air2PC-ATSC card

API changes:
- add #define DVB_API_VERSION_MINOR 1
- add struct dvb_vsb_parameters to struct dvb_frontend_parameters for FE_SET_FRONTEND

Patch by Wolfram Stering: ULE implementation, release 2

ULE is the Ultra Leightweight Encapsulation for encoding IP, IPv6, MPLS, you
name it..., into MPEG2 Transport Stream packets.  More information can be
found at the corresponding IETF working group 'ipdvb',
http://www.ietf.org/html.charters/ipdvb-charter.html

Changes from the last release include (all in dvb_net.c):
- implement the latest draft (draft-ietf-ipdvb-ule-03.txt), specifically
  the support for ULE extension headers.
- bugfixes related to handling of error conditions (e.g. TEI bit set),
  including bugs reported by Moritz Vieth and Hanno Tersteegen from
  Fraunhofer Institute.  Thanks!
- actually support MAC address filtering, if MAC address is present in
  the ULE SNDUs (D-Bit _not_ set).

necessary insmod and Makefile changes in build-2.6 for dib3000mc/p

Few small tweaks

 - add new modules to insmod script.

Imported FE_REFACTORING to HEAD

Imported stv0297 driver from tuxbox CVS

also added the driver for TerraTec's cinergyT2 to FE_REFACTORING branch

insmod cinergy.ko in "load" case

added a driver for TerraTec's brand new Cinergy T² device

Updated for new module names

Added cx22702

Added cx22702

rmmod dibusb was missing

removed vp7041 stuff from build-2.6, added dibusb and dib3000mb to build-2.6

- Make bttv modules not compile by default and add note to README.
- Fix make with -jx, where x > 1
- Force firmware to be compiled into kernel if AV7110 is compiled in.
- Modprobe firmware_class in insmod.sh, just in case.

added new driver for the USB budget devices:
- Twinhan VisionPlus VisionDTV USB-Ter DVB-T Device
- CTS Portable

documentation, helper scripts and modifications in the necessary files
have been done, hopefully.

load video-buf.ko from current dir, if it exists;
bug found by Uli Luckas

make sure i2c-core is loaded

make sure crc32 is loaded

don't try to load "input" since a 2.6 kernel will probably have it built in

add a note about insmod.sh errors for non-existant hardware,
and add some comments to insmod.sh

added 'modprobe evdev', required by av7110 remote control
fixed messages (av7110 -> DVB)

load ttusb_dec.ko for 2.6

load ttusb_dec.ko for 2.6 kernels

add cx24110

Split av7110.c into a few separate modules:

- av7110.c: initialization and demux stuff
- av7110_hw.c: lowlevel hardware access and firmware interface
- av7110_ca.c: CI and ECD
- av7110_av.c: audio/video MPEG decoder and remuxing stuff
- av7110_v4l.c: v4l interface

It's all still ugly and needs lots of namespace and coding-style
cleanups. It's probably broken, too. But it's a start.
(My main motivation is easier porting to the V4 API).

for building outside of kernel tree