For historical reasons frontend types are named after the type of modulation used in transmission.
typedef enum fe_type {
FE_QPSK, /⋆ DVB-S ⋆/
FE_QAM, /⋆ DVB-C ⋆/
FE_OFDM /⋆ DVB-T ⋆/
} fe_type_t;
Capabilities describe what a frontend can do. Some capabilities can only be supported for a specific frontend type.
typedef enum fe_caps {
FE_IS_STUPID = 0,
FE_CAN_INVERSION_AUTO = 0x1,
FE_CAN_FEC_1_2 = 0x2,
FE_CAN_FEC_2_3 = 0x4,
FE_CAN_FEC_3_4 = 0x8,
FE_CAN_FEC_4_5 = 0x10,
FE_CAN_FEC_5_6 = 0x20,
FE_CAN_FEC_6_7 = 0x40,
FE_CAN_FEC_7_8 = 0x80,
FE_CAN_FEC_8_9 = 0x100,
FE_CAN_FEC_AUTO = 0x200,
FE_CAN_QPSK = 0x400,
FE_CAN_QAM_16 = 0x800,
FE_CAN_QAM_32 = 0x1000,
FE_CAN_QAM_64 = 0x2000,
FE_CAN_QAM_128 = 0x4000,
FE_CAN_QAM_256 = 0x8000,
FE_CAN_QAM_AUTO = 0x10000,
FE_CAN_TRANSMISSION_MODE_AUTO = 0x20000,
FE_CAN_BANDWIDTH_AUTO = 0x40000,
FE_CAN_GUARD_INTERVAL_AUTO = 0x80000,
FE_CAN_HIERARCHY_AUTO = 0x100000,
FE_CAN_MUTE_TS = 0x80000000,
FE_CAN_CLEAN_SETUP = 0x40000000
} fe_caps_t;
Information about the frontend ca be queried with FE_GET_INFO.
struct dvb_frontend_info {
char name[128];
fe_type_t type;
uint32_t frequency_min;
uint32_t frequency_max;
uint32_t frequency_stepsize;
uint32_t frequency_tolerance;
uint32_t symbol_rate_min;
uint32_t symbol_rate_max;
uint32_t symbol_rate_tolerance; /⋆ ppm ⋆/
uint32_t notifier_delay; /⋆ ms ⋆/
fe_caps_t caps;
};
A message sent from the frontend to DiSEqC capable equipment.
struct dvb_diseqc_master_cmd {
uint8_t msg [6]; /⋆ { framing, address, command, data[3] } ⋆/
uint8_t msg_len; /⋆ valid values are 3...6 ⋆/
};
A reply to the frontend from DiSEqC 2.0 capable equipment.
struct dvb_diseqc_slave_reply {
uint8_t msg [4]; /⋆ { framing, data [3] } ⋆/
uint8_t msg_len; /⋆ valid values are 0...4, 0 means no msg ⋆/
int timeout; /⋆ return from ioctl after timeout ms with ⋆/
}; /⋆ errorcode when no message was received ⋆/
The voltage is usually used with non-DiSEqC capable LNBs to switch the polarzation (horizontal/vertical). When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.
typedef enum fe_sec_voltage {
SEC_VOLTAGE_13,
SEC_VOLTAGE_18
} fe_sec_voltage_t;
The continous 22KHz tone is usually used with non-DiSEqC capable LNBs to switch the high/low band of a dual-band LNB. When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.
typedef enum fe_sec_tone_mode {
SEC_TONE_ON,
SEC_TONE_OFF
} fe_sec_tone_mode_t;
The 22KHz tone burst is usually used with non-DiSEqC capable switches to select between two connected LNBs/satellites. When using DiSEqC epuipment this voltage has to be switched consistently to the DiSEqC commands as described in the DiSEqC spec.
typedef enum fe_sec_mini_cmd {
SEC_MINI_A,
SEC_MINI_B
} fe_sec_mini_cmd_t;
Several functions of the frontend device use the fe_status data type defined by
typedef enum fe_status {
FE_HAS_SIGNAL = 0x01, /⋆ found something above the noise level ⋆/
FE_HAS_CARRIER = 0x02, /⋆ found a DVB signal ⋆/
FE_HAS_VITERBI = 0x04, /⋆ FEC is stable ⋆/
FE_HAS_SYNC = 0x08, /⋆ found sync bytes ⋆/
FE_HAS_LOCK = 0x10, /⋆ everything's working... ⋆/
FE_TIMEDOUT = 0x20, /⋆ no lock within the last ~2 seconds ⋆/
FE_REINIT = 0x40 /⋆ frontend was reinitialized, ⋆/
} fe_status_t; /⋆ application is recommned to reset ⋆/
to indicate the current state and/or state changes of the frontend hardware.
The kind of parameters passed to the frontend device for tuning depend on the kind of hardware you are using. All kinds of parameters are combined as an union in the FrontendParameters structure:
struct dvb_frontend_parameters {
uint32_t frequency; /⋆ (absolute) frequency in Hz for QAM/OFDM ⋆/
/⋆ intermediate frequency in kHz for QPSK ⋆/
fe_spectral_inversion_t inversion;
union {
struct dvb_qpsk_parameters qpsk;
struct dvb_qam_parameters qam;
struct dvb_ofdm_parameters ofdm;
} u;
};
For satellite QPSK frontends you have to use the QPSKParameters member defined by
struct dvb_qpsk_parameters {
uint32_t symbol_rate; /⋆ symbol rate in Symbols per second ⋆/
fe_code_rate_t fec_inner; /⋆ forward error correction (see above) ⋆/
};
for cable QAM frontend you use the QAMParameters structure
struct dvb_qam_parameters {
uint32_t symbol_rate; /⋆ symbol rate in Symbols per second ⋆/
fe_code_rate_t fec_inner; /⋆ forward error correction (see above) ⋆/
fe_modulation_t modulation; /⋆ modulation type (see above) ⋆/
};
DVB-T frontends are supported by the OFDMParamters structure
struct dvb_ofdm_parameters {
fe_bandwidth_t bandwidth;
fe_code_rate_t code_rate_HP; /⋆ high priority stream code rate ⋆/
fe_code_rate_t code_rate_LP; /⋆ low priority stream code rate ⋆/
fe_modulation_t constellation; /⋆ modulation type (see above) ⋆/
fe_transmit_mode_t transmission_mode;
fe_guard_interval_t guard_interval;
fe_hierarchy_t hierarchy_information;
};
In the case of QPSK frontends the Frequency field specifies the intermediate
frequency, i.e. the offset which is effectively added to the local oscillator frequency (LOF) of
the LNB. The intermediate frequency has to be specified in units of kHz. For QAM and
OFDM frontends the Frequency specifies the absolute frequency and is given in
Hz.
The Inversion field can take one of these values:
typedef enum fe_spectral_inversion {
INVERSION_OFF,
INVERSION_ON,
INVERSION_AUTO
} fe_spectral_inversion_t;
It indicates if spectral inversion should be presumed or not. In the automatic setting
(INVERSION_AUTO) the hardware will try to figure out the correct setting by
itself.
The possible values for the FEC_inner field are
typedef enum fe_code_rate {
FEC_NONE = 0,
FEC_1_2,
FEC_2_3,
FEC_3_4,
FEC_4_5,
FEC_5_6,
FEC_6_7,
FEC_7_8,
FEC_8_9,
FEC_AUTO
} fe_code_rate_t;
which correspond to error correction rates of 1/2, 2/3, etc., no error correction or auto detection.
For cable and terrestrial frontends (QAM and OFDM) one also has to specify the quadrature modulation mode which can be one of the following:
typedef enum fe_modulation {
QPSK,
QAM_16,
QAM_32,
QAM_64,
QAM_128,
QAM_256,
QAM_AUTO
} fe_modulation_t;
Finally, there are several more parameters for OFDM:
typedef enum fe_transmit_mode {
TRANSMISSION_MODE_2K,
TRANSMISSION_MODE_8K,
TRANSMISSION_MODE_AUTO
} fe_transmit_mode_t;
typedef enum fe_bandwidth {
BANDWIDTH_8_MHZ,
BANDWIDTH_7_MHZ,
BANDWIDTH_6_MHZ,
BANDWIDTH_AUTO
} fe_bandwidth_t;
typedef enum fe_guard_interval {
GUARD_INTERVAL_1_32,
GUARD_INTERVAL_1_16,
GUARD_INTERVAL_1_8,
GUARD_INTERVAL_1_4,
GUARD_INTERVAL_AUTO
} fe_guard_interval_t;
typedef enum fe_hierarchy {
HIERARCHY_NONE,
HIERARCHY_1,
HIERARCHY_2,
HIERARCHY_4,
HIERARCHY_AUTO
} fe_hierarchy_t;