Mailing List archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[linux-dvb] AW: WG: J2 Connector Rev 1.3 + Lirc
Hallo,
habe dein Posting wohl nicht ganz gelesen,
den Part mit dem "cd lirc" usw. nicht mitbekommen. ;-(
O.k., nach dem laden sollte ein "registered" kommen.
Im lirc_dvb ist standardmäßig das debugging aller codes
an, es sollten also dann Messages erscheinen.
Falls nicht: Kannst du die Codierung der Fernbedienung
ändern?
Die Schaltung klappt nur mit Happauge-gemäßen
Befehlen (im RC-5? o.ä Format). Irgendjemand hatte
m.E. mal LOEWE-Befehle genannt...
Bis denn
Jörg
-----Ursprüngliche Nachricht-----
Von: Eilers, Jörg
Gesendet: Mittwoch, 17. Juli 2002 12:30
An: 'nils becker'
Cc: 'linux-dvb@linuxtv.org'
Betreff: AW: [linux-dvb] WG: J2 Connector Rev 1.3 + Lirc
Hi,
because I'm not at home, I can't see if I did some other
things, but here is what I remember:
You have to compile the lirc_dvb.c in [...]/DVB/driver/lirc
(just do a make there) and load the resulting module.
I changed my makefile in DVB/driver for the "insmod", "rmmod" and
"reload" to do this for me.
If lircd is running, you should see a startup message like
"lirc device registered" and after that, you should be able
to see debug messages for every RC-key (Console ALT+F10 in SuSE ;-))
like "ircom = xxxx" (I really can't remember that).
You can use this values to create the config-file for lirc.
Hope that helps
Jörg
-----Ursprüngliche Nachricht-----
Von: nils becker [mailto:nils.becker@n-becker.de]
Gesendet: Montag, 15. Juli 2002 23:46
An: linux-dvb@linuxtv.org
Betreff: J2 Connector Rev 1.3 + Lirc
Hi,
I am using SUSE 7.3 DVB-s Rev. 1.3 and DVB Drivers and I am trying to get
the Lirc Driver lirc_dvb to work. I searched the mailing list and tried all
the advice, but I can not get my Ir receiver to produce any codes.
What I do:
# cd /usr/local/src/DVB/driver
# make insmod
# cd lirc
# make insmod
# lircd
all modules load alright and the DVB driver is running. I can watch n-tv
I build the receiver from www.linuxdvb.tv and I get 0.3V on pin 9 at J2 with
no button pressed and 0.6V when I press buttons on my remote(not a
Hauppauge). So everything looks fine, but I cannot get any reaction from
lircd. So I looked at the sources from lirc_dvb and lirc_dev and I was
wondering where I could put some debugging code to see if my remote was
working at all and what codes I should use, since irrecord does not work.
Any suggestions on where I should look or what else could be wrong.
Thanks in advance.
NB
--
Info:
To unsubscribe send a mail to listar@linuxtv.org with "unsubscribe
linux-dvb" as subject.
--
Info:
To unsubscribe send a mail to listar@linuxtv.org with "unsubscribe linux-dvb" as subject.
Home |
Main Index |
Thread Index