[vdr] Re: VDR, LIRC and the Hauppauge DVB-s 2.1 remote control

["Walter, Marcel" <Marcel.Walter@drkw.com>]

Hello ...

Yes, I did but I had the same difficulties like the ones you described...
Lircd thougt some buttons were pushed permanently ...

Try to use this lircd.conf: <http://www.uni-mainz.de/~martin/lircd.conf> 

For more information ( this one was very good ) try this URL:  (in German)
http://www.dvbforum.com/noncgi/ultimatebb.php?ubb=get_topic&f=17&t=000168&p=
2
There are two different instructions... Try the last one (posted by Jo)

kind regards,
Marcel


> -----Original Message-----
> From:	Markus Dahlweid [SMTP:dahlweid@gmx.de]
> Sent:	Tuesday, January 15, 2002 15:12
> To:	vdr@linuxtv.org
> Subject:	[vdr] VDR, LIRC and the Hauppauge DVB-s 2.1 remote control
> 
> Hi,
> 
> I recently found out, that the DVB-driver is supported by the latest
> CVS version of lirc. I compiled the lirc modules of the DVB driver and
> configured lirc to access the IR-receiver of my Hauppauge DVBs
> Revision 2.1.
> 
> When I am using irrecord to get the remote control commands from the
> Hauppauge remote control the detection of the toggle bit fails. Right
> now my lirc-configuration looks as follows:
> 
> --- lircd.conf ---
> begin remote
> 
>    name  HauppaugeVDR
>    bits           8
>    eps            30
>    aeps          100
> 
>    one             0     0
>    zero            0     0
>    pre_data_bits   24
>    pre_data       0x0
>    gap          199970
>    min_repeat      14
>    toggle_bit      0
> 
> 
>        begin codes
>            Up                       0x0000000000000020
>            Down                     0x0000000000000021
>            Menu                     0x000000000000000F
>            Ok                       0x000000000000002E
>            Back                     0x000000000000000C
>            Left                     0x0000000000000011
>            Right                    0x0000000000000010
>            Red                      0x000000000000000D
>            Green                    0x0000000000000022
>            Yellow                   0x000000000000001E
>            Blue                     0x0000000000000026
>            0                        0x0000000000000000
>            1                        0x0000000000000001
>            2                        0x0000000000000002
>            3                        0x0000000000000003
>            4                        0x0000000000000004
>            5                        0x0000000000000005
>            6                        0x0000000000000006
>            7                        0x0000000000000007
>            8                        0x0000000000000008
>            9                        0x0000000000000009
>        end codes
> 
> end remote
> --- end of file ---
> 
> This seems basically to be the correct configuration, since I can use
> the remote control to send VDR some commands. But using the Up and
> Down buttons in any VDR On Screen Menu, which displays a list of
> items, has some stange effect: the marked line moves up/down to the
> end/beginning of the displayed list. Right now there seems to be no
> way to access any other items shown in the list.
> 
> Has anyone managed to configure LIRC for the the Hauppauge remote
> control so that everything works as expected?
> 
> Bye,
> Markus
> 
> 
> 


If you have received this e-mail in error or wish to read our e-mail disclaimer statement and monitoring policy, please refer to
http://www.drkw.com/disc/email/ or contact the sender.