I found some settings that work:
S5.0E 11700 V 9750 t v W15 [E0 10 38 F0] W100 [E0 10 38 F0] W100 [E0 11 00] W100 A W15 t
S5.0E 99999 V 10600 t v W15 [E0 10 38 F1] W100 [E0 10 38 F1] W100 [E0 11 00] W100 A W15 T
S5.0E 11700 H 9750 t V W15 [E0 10 38 F2] W100 [E0 10 38 F2] W100 [E0 11 00] W100 A W15 t
S5.0E 99999 H 10600 t V W15 [E0 10 38 F3] W100 [E0 10 38 F3] W100 [E0 11 00] W100 A W15 T
S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W100 [E0 10 38 F4] W100 [E0 11 00] W100 B W15 t
S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W100 [E0 10 38 F5] W100 [E0 11 00] W100 B W15 T
S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W100 [E0 10 38 F6] W100 [E0 11 00] W100 B W15 t
S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W100 [E0 10 38 F7] W100 [E0 11 00] W100 B W15 T
S16.0E 11700 V 9750 t v W15 [E0 10 38 F8] W100 [E0 10 38 F8] W100 [E0 11 00] W100 A W15 t
S16.0E 99999 V 10600 t v W15 [E0 10 38 F9] W100 [E0 10 38 F9] W100 [E0 11 00] W100 A W15 T
S16.0E 11700 H 9750 t V W15 [E0 10 38 FA] W100 [E0 10 38 FA] W100 [E0 11 00] W100 A W15 t
S16.0E 99999 H 10600 t V W15 [E0 10 38 FB] W100 [E0 10 38 FB] W100 [E0 11 00] W100 A W15 T
S19.2E 11700 V 9750 t v W15 [E0 10 38 FC] W100 [E0 10 38 FC] W100 [E0 11 00] W100 B W15 t
S19.2E 99999 V 10600 t v W15 [E0 10 38 FD] W100 [E0 10 38 FD] W100 [E0 11 00] W100 B W15 T
S19.2E 11700 H 9750 t V W15 [E0 10 38 FE] W100 [E0 10 38 FE] W100 [E0 11 00] W100 B W15 t
S19.2E 99999 H 10600 t V W15 [E0 10 38 FF] W100 [E0 10 38 FF] W100 [E0 11 00] W100 B W15 T
They are in the order of ports on switch.
A non proved explanation is that the LNB needs 100ms to powerup until it can work.
Regards,
Ilariu
On 1/29/07, Ilariu Raducan <
ilariu@gmail.com> wrote:
I'm using VDR4You distribution, and I don't want to install kaffeine on it.
I want to keep it small ;)
I need to check if vdr is sending something that is not suposed to.
Note that vdr works for channels on LNB1 if you disable diseqc in the setup.
Ilariu
On 1/29/07, Gregoire Favre <
Gregoire.Favre@gmail.com> wrote:
On Mon, Jan 29, 2007 at 01:32:16PM +0000, Ilariu Raducan wrote:
> I also have problems with 4 quad LNBs on a diseqc switch (1.0 and another
> 2.0)
> If I plug out the cable from the card and plug it back again (reset switch
> and LNBs)
> I can use szap to change the channels. I believe the quad LNBs have diseqc
> switch
> inside and at reset they are in backward compatible mode (Tone/Voltage).
> In Diseqc specifications/recommendations they recommend the diseqc LNB
> should ignore responding
> to Tone/Voltage commands when they receive one diseqc command.
> Unfortunately, I did not find the proper diseqc commands for the LNBs.
>
> I will try today a workaround to reset the LNB before sending the
> diseqc.conf sequence in backward compatible mode:
> - switch to another LNB (hope the power will be cut for the one I need for
> the channel)
> - do the sequence for current channel
> t v [E0 10 38 FF] W500 (switch to LNB4 and wait 500) [E0 10 38 F0] W100 A
> W15 t (switch to LNB1, wait for power to stabilize, use back compatible)
>
> If I am lucky enough the switch will cut the power for the LNB1 when I
> switch to LNB4.
>
> Does anybody knows the Diseqc commands for Quad LNBs??
Very stangely, under kaffeine here all runs perfectly ???
Did you also try to use your quiete similar setup under kaffeine ?
I have tried an hudge number of setup, including diseqc reset, resent of
messages...
Maybe there is only two VDR user with quad lnb in the world using
diseqc ?
--
Grégoire FAVRE
http://gregoire.favre.googlepages.com
http://www.gnupg.org
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr