On 8/15/2013 9:08 PM, Brian-Imap
wrote:
On 8/15/2013 5:58 PM, Arthur wrote:
15.08.2013
18:37, Brian-Imap kirjutas:
On 8/14/2013 10:16 PM, Arthur wrote:
14.08.2013 19:01, Brian-Imap
kirjutas:
On 8/11/2013 11:43 AM, Brian-Imap
wrote:
On 8/8/2013 10:22 PM, Lars
Hanisch wrote:
Am 08.08.2013 16:23, schrieb
Brian-Imap:
On 8/7/2013 9:58 PM, Lars
Hanisch wrote:
Hi,
Am 07.08.2013 21:04, schrieb Brian-Imap:
Hi,
I now a have a 4 Tuner Cine S2 setup that I
want to run with 3
cables, I want to keep the fourth cable for a
test VDR.
Reading about this I only see how to do it
together with the
Dynamite Plugin, is that correct that I must
use that
Plugin to get it to work for VDR?
I am currently running a plain VDR setup on
Ubuntu, with very few
plugins and had no need for the Dynamite
Plugin
up till now.
You don't really need dynamite. If you want to
omit the fourth
tuner (in kernel count order), you can start vdr
with
the -D parameter (see vdr --help).
vdr -D0 -D1 -D2 <other parameters as
usual>
Regards,
Lars.
Cheers Brian
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Hi Lars,
OK I knew about this, but I thought that the
Card/Tuners numbers
could change
from boot to boot. Are you saying that they will
not change?
If it's one bridge with 4 tuners, I doubt their
order will change.
You may want to read about "device bonding", where
you split one
cable on two tuners so they share polarisation and
band, but may be tuned to different transponders.
But I'm a cable user, I don't know much about it,
just that there
are some people out there who use it successfully.
:)
Regards,
Lars.
Cheers Brian
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Hi,
thanks for the tips, unfotunately I ended up needing
to keep using a
FF Card for a short while.
So I followed the CT tip and added a TT C-2300 Cable
FF card that is
not connected to cable at all.
That part seems to work really well.
Using the -D parameter in VDR I limited VDR to using
the first 4 DVB
Devices and this is what it gave me:
Aug 11 11:09:31 localhost vdr: [936] frontend 0/0
provides
DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Aug 11 11:09:31 localhost vdr: [936] frontend 1/0
provides DVB-C with
QAM16,QAM32,QAM64,QAM128,QAM256 ("ST STV0297 DVB-C")
Aug 11 11:09:31 localhost vdr: [936] frontend 2/0
provides
DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
Aug 11 11:09:31 localhost vdr: [936] frontend 4/0
provides
DVB-S,DVB-S2,DSS with QPSK ("STV090x Multistandard")
So tuners 1-3 of the Cine S2 and Duoflex are now in
use. DBV device 1
provides nothing but MPEG output.
I guess I'll keep an eye on the DVB device ordering
for a while to see
how it goes.
Cheers Brian
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Hi,
well the DVB device numbering is not consistent:
"VDR-Test-Cellar(SDA2): 15:25 [995] frontend 3/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 15:25 [995] frontend 2/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 15:25 [995] frontend 1/0
provides DVB-C with
QAM16,QAM32,QAM64,QAM128,QAM256 (""ST STV0297 DVB"
"VDR-Test-Cellar(SDA2): 15:25 [995] frontend 0/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 05:10 [1018] frontend 3/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 05:10 [1018] frontend 2/0
provides DVB-C with
QAM16,QAM32,QAM64,QAM128,QAM256 (""ST STV0297 DV"
"VDR-Test-Cellar(SDA2): 05:10 [1018] frontend 1/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 05:10 [1018] frontend 0/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 06:52 [1080] frontend 3/0
provides DVB-C with
QAM16,QAM32,QAM64,QAM128,QAM256 (""ST STV0297 DV"
"VDR-Test-Cellar(SDA2): 06:52 [1080] frontend 2/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 06:52 [1080] frontend 1/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 06:52 [1080] frontend 0/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 19:16 [1015] frontend 3/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 19:16 [1015] frontend 2/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
"VDR-Test-Cellar(SDA2): 19:16 [1015] frontend 1/0
provides DVB-C with
QAM16,QAM32,QAM64,QAM128,QAM256 (""ST STV0297 DV"
"VDR-Test-Cellar(SDA2): 19:16 [1015] frontend 0/0
provides
DVB-S,DVB-S2,DSS with QPSK (""STV090x Multistandard"")"
Up till now it has not been a problem, the one without a
cable must be
4/0. Still I am wondering if this can be controlled?
Before VDR start unload the DVB drivers, then load
DVBTTPCI first and
give it a short delay and then load DDBridge maybe?
Still, then is it then guaranteed that DDBridge will
number its 4 tuners
correctly?
Cheers Brian
Do you tried udev rules for controlling multiple DVB
device numbering?
br,
Arthur
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Arthur,
No. Please tell me how?
Cheers Brian
At the moment I don't use it, but I found it from my archive.
Attached file has been placed in the /etc/udev/rules.d folder
in my Slackware PC.
br,
Arthur
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Arthur, thanks very much
I'll only get around to trying it at the weekend though.
Cheers
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Hi,
so I tried to look for some kind of info to help me identify the
tuners, this is the most interesting bit I guess:
VDR-test-cellar (SDB1): udevadm info --query=all
--name=/dev/dvb/adapter1/frontend0 --attribute-walk
looking at device
'/devices/pci0000:00/0000:00:0d.0/0000:02:00.0/dvb/dvb1.frontend0':
KERNEL=="dvb1.frontend0"
SUBSYSTEM=="dvb"
DRIVER==""
VDR-test-cellar (SDB1): udevadm info --query=all
--name=/dev/dvb/adapter0/frontend0 --attribute-walk
looking at device
'/devices/pci0000:00/0000:00:0d.0/0000:02:00.0/dvb/dvb0.frontend0':
KERNEL=="dvb0.frontend0"
SUBSYSTEM=="dvb"
DRIVER==""
VDR-test-cellar (SDB1): udevadm info --query=all
--name=/dev/dvb/adapter2/frontend0 --attribute-walk
looking at device
'/devices/pci0000:00/0000:00:0d.0/0000:02:00.0/dvb/dvb2.frontend0':
KERNEL=="dvb2.frontend0"
SUBSYSTEM=="dvb"
DRIVER==""
VDR-test-cellar (SDB1): udevadm info --query=all
--name=/dev/dvb/adapter3/frontend0 --attribute-walk
looking at device
'/devices/pci0000:00/0000:00:06.0/0000:01:06.0/dvb/dvb3.frontend0':
KERNEL=="dvb3.frontend0"
SUBSYSTEM=="dvb"
DRIVER==""
VDR-test-cellar (SDB1): udevadm info --query=all
--name=/dev/dvb/adapter4/frontend0 --attribute-walk
looking at device
'/devices/pci0000:00/0000:00:0d.0/0000:02:00.0/dvb/dvb4.frontend0':
KERNEL=="dvb4.frontend0"
SUBSYSTEM=="dvb"
DRIVER==""
At the moment I cannot find anything to identify the 4 Tuners on
the Cine S2, the FF on 01:06 is easy.
I got hit by tuning problems a few days ago as the tuner without a
cable was given FE3/0. The FF got FE4/0
at that time. I'm wondering if the DDBridge driver will always
number in the correct order.
So I guess I'll try to make the FF FE0/0, and hope that the
DDBRidge driver will do the rest.
Cheers Brian
_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
Not so easy.