[linux-dvb] Twinhan DTV TER-CI 3030 Mantis DVB-T
abraham.manu at gmail.com
Sat Nov 25 11:48:36 CET 2006
Andreas Vinsander wrote:
> I recently subscribed to this maillist and have since done some reading
> up on the posts. And found this from the "Mantis
Sorry for the late reply ..
> Subject: Re: [linux-dvb] Mantis VP-1027/VP-1033/VP-1034/VP-2033/VP-3033
> From: Manu Abraham
> Date: Sat, 07 Oct 2006 05:11:49 -0700
> Lauri Tischler wrote:
>> Does this apply also to these cards
>> - Twinhan DTV TER-CI 3030 Mantis DVB-T
>> - Twinhan DTV TER-CI 3040 DVB-T PCI
>> - Twinhan DTV SAT-CI 1030 DVB-S PCI
> No. The dst module supports these cards.
Apologies, a mistake from my side. The 3030 Mantis DVB-T is a Mantis
based card. Sorry for that stupid mistake.
> I have one of those Twinhan DTV TER-CI 3030 Mantis DVB-T pci cards, but
> the dst module (from gentoo package v4l-dvb-hg-0.1-r2, which seems to
> pull the source via hg from the dvb repository) doesn't seem to
> recognize the card. dmesg and logfiles shows that the modules are loaded
> but they don't find a bt8x8 chip and thus no /dev/dvb/ entries are
> created (udev-103). I have tried the modules supplied by the kernel
> gentoo-sources-2.6.18-r2 (do I need to try vanilla 2.6.19-rc5?) as well,
> with the same results.
> I am running 64bit Linux on an Athlon64 X2 3800+ stuffed into an ASUS
> M2NPV-VM motherboard. Both PCI slots are used, one for the Twinhan card
> and the other for an atheros based WiFi card (which works alright btw).
> I provide some lspci & pcimodules output down below, what else can I do
> to find out what goes wrong here? Is it possible that Manu missed
> something when he stated that this card was supported by the dst module?
> # lspci -vv
> 04:08.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV PCI
> Bridge Controller [Ver 1.0] (rev 01)
> Subsystem: Twinhan Technology Co. Ltd Unknown device 0024
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 32 (2000ns min, 63750ns max)
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at fdaff000 (32-bit, prefetchable) [size=4K]
This is a Mantis based card supported by the Mantis driver and not the dst.
> # lspci -nv
> 04:08.0 0480: 1822:4e35 (rev 01)
> Subsystem: 1822:0024
> Flags: bus master, medium devsel, latency 32, IRQ 5
> Memory at fdaff000 (32-bit, prefetchable) [size=4K]
> # pcimodules
> No sign of any DVB drivers compliant with the card at 04:08.0
This card VP-3030 would use the MT352 driver rather than the ZL10353
driver as compared to the VP-3033
> I have quite good programming skills (C++, C) and would be happy to help
> out as much as my wife allows me ;-)
More information about the linux-dvb