[linux-dvb] Leadtek WinFast PxDVR3200 H
stev391 at email.com
stev391 at email.com
Mon Jan 26 23:53:50 CET 2009
> ----- Original Message -----
> From: "Wayne and Holly" <wayneandholly at alice.it>
> To: stev391 at email.com
> Subject: RE: Leadtek WinFast PxDVR3200 H
> Date: Mon, 26 Jan 2009 18:09:55 +0100
> It would appear that Myth is the source of the problem. Of the three
> transponders that scan finds, only the last one contains unencrypted
> channels actually transmitting content. Using the same channels.conf file
> gxine is able to tune to the channels. I have tried carrying out a full
> manual scan in myth using the good transponder's details and myth is now
> able to detect the channels, but still won't show them.
> I suspect this is purely a myth problem, do you still want me to post the
> debug info for the two modules?
> > -----Original Message-----
> > From: stev391 at email.com [mailto:stev391 at email.com] Sent: Sunday, 25 January 2009 12:28 p.m.
> > To: Wayne and Holly
> > Cc: linux-dvb at linuxtv.org
> > Subject: Re: Leadtek WinFast PxDVR3200 H
> > > Hello list,
> > > I have a Leadtek WinFast PxDVR3200 H that I am attempting to utilise > with MythTV. The
> > Wiki site states that experimental support exists > for the DVB side and that "Successful
> > tuning of typical Australian > channels" has been achieved. I am able to create a
> > channels.conf > (attached) using scan, and am then able to tune using mythtv-setup, > however
> > none of these channels are viewable with the mythfrontend due > to it being unable to gain a
> > lock.
> > > > Relevant bits and pieces:
> > > > scan, using the latest it-Varese file scan is able to tune to three of > the five
> > transponders as per the attached file "scan". It also scans > on 800000000Hz but I have no
> > idea why.
> > > > The file leadtek.dmesg contains the relevant info from dmesg (and
> > > messages.log) regarding the initialisation of the card itself. There > are no error
> > messages at any time (that I am aware of) despite all of > my fiddling about.
> > > > Of the three transponders that are in my channels.conf file, the third > one
> > > (618000000Hz) causes an error when tuning in mythtv-setup. It states that
> > > channels are found but the tsid is incorrect. As such, only the first two
> > > successful transponders (706000000 and 602000000) are tuned by myth.
> > > > When I attempt to view the tuned channels, myth is unable to gain a > lock on any of them.
> > The reported signal strength is about 58% and > the S/N varies between 3 and 3.8dB. I am
> > able to tune DVB-T channels > on my TV using the same aerial cable but am wondering if signal
> > > strength is an issue.
> > > > I am running it on Kubuntu with a 2.6.24-19 kernel, I have a recent > version of the
> > v4l-dvb tree (approx Nov 08) and am using firmware > version 2.7. I haven't updated the
> > drivers or the firmware as I have > no reason to believe there are changes that would effect
> > this. That > said, if someone thinks there has been changes I will get straight on > it.
> > > > I am more than happy to provide more debugging info if required (if > you are willing to
> > tell me where else to look) and appreciate any help > provided.
> > > > Cheers
> > > Wayne
> > Wayne,
> > Can you load the cx23885 and tuner_xc2028 module with debug enabled and provide the dmesg
> > output.
> > You can do this by putting the following lines in /etc/modprobe.d/options options tuner_xc2028
> > debug=1 options cx23885 debug=1
> > Can you split the dmesg output into the following sections:
> > 1) Initial boot up or first module load
> > 2) First access of the card for tuning/scanning
> > 3) while scanning for channels with scan-dvb
> > 4) while scanning for channels with MythTV
> > 5) while trying to tune channels with MythTV
> > Have you tried to watch TV with xine or other non-MythTV programs? (at one stage I did have a
> > problem with MythTV but it worked in gxine).
> > Regards,
> > Stephen.
When replying to emails, please ensure that the mailing list is in the CC. So if anyone else is having the same issue they can join the thread or use this information in the future. Also please post the reply at the bottom of the email, so that anybody later can read the responses in chronological order from top to bottom.
I would be interested to see the debug output, for the following conditions:
1) scan-dvb vs MythTV scan
2) Tuning channels in gxine Vs MythTV
If we can spot an obvious problem, we can possibly provide the information to the MythTV devs (or I might get adventurous write a patch for them)
Be Yourself @ mail.com!
Choose From 200+ Email Addresses
Get a Free Account at www.mail.com
More information about the linux-dvb