View source for WinTV PAL-B/GI 61314 REV B1M

[[Image:Hauppauge_WinTV_61314.jpg|right|thumb|200px|Bt878 based PCI, analog PAL]]

A Bt878 based PCI card from Hauppague.  

The card is supported under Linux. Tested on kernel 2.6.32.


==Overview/Features==

* PCI interface
* Inputs: Antenna, S-Video In, Composite, Audio Line In
* Outputs: Audio Line Out 

===Components Used===
* Bt878 (video and audio capture)
* MSP3415D (sound processor)
* Philips FI1216 MK2 (tuner)


===Identification===

 # lspci -vvvnnn
 04:03.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 02)
 	Subsystem: Hauppauge computer works Inc. Device [0070:13eb]
 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
 	Latency: 16 (4000ns min, 10000ns max)
 	Interrupt: pin A routed to IRQ 22
 	Region 0: Memory at fdcff000 (32-bit, prefetchable) [size=4K]
 	Kernel driver in use: bttv
 	Kernel modules: bttv
 
 04:03.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 02)
 	Subsystem: Hauppauge computer works Inc. Device [0070:13eb]
 	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
 	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
 	Latency: 64 (1000ns min, 63750ns max)
 	Interrupt: pin A routed to IRQ 22
 	Region 0: Memory at fdcfe000 (32-bit, prefetchable) [size=4K]
 	Kernel driver in use: Bt87x
 	Kernel modules: snd-bt87

==Making it Work==
Supported by V4l2.

===Firmware===
No firmware required.

===Drivers===
''Provide the details of where the drivers and patches and necessary tools are available.''

===Sample Kernel Output===

 # dmesg
 [    5.863420] Linux video capture interface: v2.00
 ...
 [    6.086075] bttv: driver version 0.9.18 loaded
 [    6.086077] bttv: using 8 buffers with 2080k (520 pages) each for capture
 [    6.086128] bttv: Bt8xx card found (0).
 [    6.086136] bttv 0000:04:03.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
 [    6.086144] bttv0: Bt878 (rev 2) at 0000:04:03.0, irq: 22, latency: 16, mmio: 0xfdcff000
 [    6.086165] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
 [    6.086166] bttv0: using: Hauppauge (bt878) [card=10,autodetected]
 [    6.086168] IRQ 22/bttv0: IRQF_DISABLED is not guaranteed on shared IRQs
 [    6.088682] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
 [    6.119311] tveeprom 0-0050: Hauppauge model 61314, rev B1M , serial# 3160514
 [    6.119313] tveeprom 0-0050: tuner model is Philips FI1216 MK2 (idx 8, type 5)
 [    6.119315] tveeprom 0-0050: TV standards PAL(B/G) (eeprom 0x04)
 [    6.119317] tveeprom 0-0050: audio processor is MSP3415 (idx 6)
 [    6.119318] tveeprom 0-0050: has no radio
 [    6.119319] bttv0: Hauppauge eeprom indicates model#61314
 [    6.119321] bttv0: tuner type=5
 ...
 [    6.154143] msp3400 0-0040: MSP3410D-B4 found @ 0x80 (bt878 #0 [sw])
 [    6.154144] msp3400 0-0040: msp3400 supports nicam, mode is autodetect
 ...
 [    6.182051] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
 [    6.212688] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
 [    6.215113] tuner-simple 0-0061: creating new instance
 [    6.215115] tuner-simple 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
 [    6.215778] bttv0: registered device video1
 [    6.215798] bttv0: registered device vbi0
 [    6.233580] bttv0: PLL: 28636363 => 35468950 .

===Remote Control Support===
Unknown - not tested.

==External Links==

* [http://www.hauppauge.com/site/support/support_pci_878.html Hauppague support page]


[[Category:Analog PCI Cards]]