TODO RC: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| (22 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== Minor bugs/improvement == |
|||
Investigation needed: |
|||
* if driver depends on RC_CORE, change this to select RC_CORE, depends on INPUT? OR use a patch like https://patchwork.linuxtv.org/patch/40601/ and remove "depends on RC_CORE". |
|||
* struct ir_raw_event_ctrl member prev_ev. Investigate if this can be removed. |
|||
* mceusb can do wakeups. Allow this to be configured |
|||
* serial_ir tx w/ softcarrier, does it work on 32 bit? "new_duty_cycle * NSEC_PER_SEC" > 2^32. |
|||
* ir-keytable should display and allow you to configure wakeup protocol and scancode (protocol?) |
|||
* Kconfig RC_CORE should not depend on MEDIA_SUPPORT |
|||
* Can sir_ir and/or serial_ir use serdev |
|||
* depends on RC_COREC -> select RC_CORE, depends on INPUT? |
|||
* Make the kernel mapping rc_proto:scancode -> keycode, not just scancode. This should reduce the number of possible conflicts. |
|||
* RC device RC_DRIVER_IR_RAW_TX leaks dev->raw on rc_unregister_device()? |
|||
* ir-ctl should list available devices if run without any argument and allow to select device based on rc (based on /sys/class/rc/). |
|||
* Unplug iguanair with lirc chardev open causes kernel to go bang |
|||
* bpf ir decoders need a way of specifying minimum timeout and repeat period |
|||
* Compile kernel with KASAN. mceusb says: |
|||
* driver for sasem remote controller |
|||
[ 56.365080] BUG: KASAN: slab-out-of-bounds in mceusb_dev_printdata+0xdc/0x830 [mceusb] at addr ffff8801df071d0a |
|||
* test if pwm-ir-tx can replace ir-rx51.c driver on n900 hardware |
|||
* saa7134 should add trailing space (timeout handling). Once this is fixed, implement the following item. |
|||
* ir_raw_event_store_edge() should not use REP_DELAY. |
|||
Worked needed: |
|||
* ir-spi says "Unspecified device" in dmesg since ir-spi does not set input_name; rename input_name to device_name for all RC devices. |
|||
* pwm gpio transmitter needed (Sean Young working on this) |
|||
* bitbang gpio transmitter needed (Sean Young working on this) |
|||
* lirc_zilog rc core driver (Sean Young working on this) |
|||
* Once lirc_zilog is removed, remove lirc kapi. |
|||
ir-keytable changes needed. |
|||
* Cannot list RC core devices if one of them is of type RC_DRIVER_IR_RAW_TX |
|||
* Without CONFIG_INPUT_EVDEV ir-keytable goes bang |
|||
* "ir-ctl -S rc6_mce:0x800f0410" does not work on 32-bit |
|||
* MS MCE Keyboard keymap needs multiple protocols. Keymap needed to select it. https://www.mail-archive.com/linux-media@vger.kernel.org/msg115706.html |
|||
Latest revision as of 15:32, 21 September 2018
Minor bugs/improvement
- if driver depends on RC_CORE, change this to select RC_CORE, depends on INPUT? OR use a patch like https://patchwork.linuxtv.org/patch/40601/ and remove "depends on RC_CORE".
- mceusb can do wakeups. Allow this to be configured
- ir-keytable should display and allow you to configure wakeup protocol and scancode (protocol?)
- Can sir_ir and/or serial_ir use serdev
- Make the kernel mapping rc_proto:scancode -> keycode, not just scancode. This should reduce the number of possible conflicts.
- ir-ctl should list available devices if run without any argument and allow to select device based on rc (based on /sys/class/rc/).
- bpf ir decoders need a way of specifying minimum timeout and repeat period
- driver for sasem remote controller
- test if pwm-ir-tx can replace ir-rx51.c driver on n900 hardware