Talk:PcHDTV: Difference between revisions
No edit summary |
|||
| Line 5: | Line 5: | ||
I think we should get some of the folks in the pcHDTV forum to help construct an up-to-date Current Driver Status page. It's a pain having to search through the forums for scattered bits of information. Unfortunately, I would not be able to provide much help because the HD reception in my area is poor and I don't know how to get QAM working. -iconian |
I think we should get some of the folks in the pcHDTV forum to help construct an up-to-date Current Driver Status page. It's a pain having to search through the forums for scattered bits of information. Unfortunately, I would not be able to provide much help because the HD reception in my area is poor and I don't know how to get QAM working. -iconian |
||
--[[User:Iconian|Iconian]] 21:51, 20 Mar 2005 (CET) I added a Mini HOW-TO section on the main page. I don't have QAM working. The information on QAM is what I have come up with thus far. |
|||
== How do I scan for QAM channels? == |
|||
pcHDTV 3000 supports unencrypted QAM channels over cable. You must have the DVB module drivers (cx88_dvb) loaded to use QAM. [TODO add link to pcHDTV forums on DVB driver installation.] To scan for QAM channels: |
|||
<blockquote> |
|||
1. Install the 'dvb-apps' tools from cvs. See http://www.linuxtv.org. |
|||
<blockquote> |
|||
TODO add cvs instructions |
|||
</blockquote> |
|||
2. Save 'http://www.digitalregime.com/patches/channels.conf-qam-correct' to '~/.azap/channels.conf'. |
|||
</blockquote> |
|||
You should be able to scan for QAM channels using 'azap' from the dvb-apps. Run 'azap [channel]' to scan for a specified channel, e.g., 'azap c80'. Cable channels typically begin at 80. A FE_HAS_LOCK indicates a signal lock on channel. |
|||
<br><br> |
|||
MythTV 0.17 supports automagic scanning of DVB channels. Make sure you compile it with DVB support. |
|||
== How do I know if a QAM channel is encrypted? == |
|||
There does not seem to be a way to tell for certain. See this [http://www.linuxtv.org/pipermail/linux-dvb/2005-March/000460.html post] and this [http://www.linuxtv.org/pipermail/linux-dvb/2005-March/000557.html reply] (March, 2005). |
|||
== How do I record a stream from DVB? == |
|||
You can use dvbstream and dtvstream. See this [http://www.xmission.com/~pchdtv/forum/viewtopic.php?t=591 post] (March 19, 2005). |
|||
Revision as of 20:51, 20 March 2005
I just ended up here to try the HD-3000 card with DVB..I'm a Linux newbie and hardly have a clue unless I am guided well. I usually spend a lot of time searching before I post a question, but I have had the card a month and still not ready to record the Superbowl, time is short.
I am here because of a post by theCaptain on the pcHDTV forums and want to try this non pcHDTV co. driver. I am Jim on the pchdtv forum, nerdful1 on the PVR Guide. (and Meade telescope site). Trudging along now...
I think we should get some of the folks in the pcHDTV forum to help construct an up-to-date Current Driver Status page. It's a pain having to search through the forums for scattered bits of information. Unfortunately, I would not be able to provide much help because the HD reception in my area is poor and I don't know how to get QAM working. -iconian
--Iconian 21:51, 20 Mar 2005 (CET) I added a Mini HOW-TO section on the main page. I don't have QAM working. The information on QAM is what I have come up with thus far.