Compro VideoMate E600F: Difference between revisions

Revision as of 17:27, 29 September 2008

Compro VideoMate E600F (Click for High Resolution Version)

This article is a stub or is incomplete.

This article requires expansion. Please help add informative information if you can.

This is a PCIe analog TV/FM tuner card with real-time hardware MPEG-2 encoder.

It is not supported under Linux yet (non-recognized).

Overview/Features

Analog TV card (NTSC/SECAM/PAL) which supports:

480i/576i component video input,
TV stereo and SAP (MTS/NICAM/A2/EIAJ).

This card help you to:

Watch analog TV and listen to FM radio on PC,
Record TV shows with built-in real-time HQ MPEG-2 Encoder to watch them later.

Components Used

Conexant CX23885-13Z PCIe A/V Decoder,
Conexant CX23417-11Z MPEG II A/V Encoder,
XCeive XC2028ACQ Video Tuner.

Other images

CX23885-13Z PCIe A/V Decoder
CX23417-11Z MPEG II A/V Encoder
XCeive XC2028ACQ Tuner

Identification

lspci

Output of lspci:

02:00.0 Multimedia video controller: Conexant Device 8852 (rev 02)

Output of lspci -n:

02:00.0 0400: 14f1:8852 (rev 02)

Output of lspci -vvnn:

02:00.0 Multimedia video controller [0400]: Conexant Device [14f1:8852] (rev 02)
        Subsystem: Compro Technology, Inc. Device [185b:e800]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 4 bytes
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at fd600000 (64-bit, non-prefetchable) [size=2M]
        Capabilities: [40] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <2us, L1 <4us
                        ClockPM- Suprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] Vital Product Data <?>
        Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000  Data: 0000
        Capabilities: [100] Advanced Error Reporting <?>
        Capabilities: [200] Virtual Channel <?>

dmesg

Output of dmesg:

cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
cx23885[0]: Your board isn't known (yet) to the driver.  You can
cx23885[0]: try to pick one of the existing card configs via
cx23885[0]: card=<n> insmod option.  Updating to the latest
cx23885[0]: version might help as well.
cx23885[0]: Here is a list of valid choices for the card=<n> insmod option:
cx23885[0]:    card=0 -> UNKNOWN/GENERIC
cx23885[0]:    card=1 -> Hauppauge WinTV-HVR1800lp
cx23885[0]:    card=2 -> Hauppauge WinTV-HVR1800
cx23885[0]:    card=3 -> Hauppauge WinTV-HVR1250
cx23885[0]:    card=4 -> DViCO FusionHDTV5 Express
cx23885[0]:    card=5 -> Hauppauge WinTV-HVR1500Q
cx23885[0]:    card=6 -> Hauppauge WinTV-HVR1500
cx23885[0]:    card=7 -> Hauppauge WinTV-HVR1200
cx23885[0]:    card=8 -> Hauppauge WinTV-HVR1700
cx23885[0]:    card=9 -> Hauppauge WinTV-HVR1400
cx23885[0]:    card=10 -> DViCO FusionHDTV7 Dual Express
cx23885[0]:    card=11 -> DViCO FusionHDTV DVB-T Dual Express
cx23885[0]:    card=12 -> Leadtek Winfast PxDVR3200 H
CORE cx23885[0]: subsystem: 185b:e800, board: UNKNOWN/GENERIC [card=0,autodetected]
cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c bus 2 registered
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 16, latency: 0, mmio: 0xfd600000
PCI: Setting latency timer of device 0000:02:00.0 to 64

i2c scan

Output of modprobe cx23885 i2c_scan=1:

cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c scan: found device @ 0xa0  [eeprom]
cx23885[0]: i2c scan: found device @ 0xd0  [???]
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c scan: found device @ 0xc2  [tuner/mt2131/tda8275/xc5000/xc3028]
cx23885[0]: i2c bus 2 registered
cx23885[0]: i2c scan: found device @ 0x66  [???]
cx23885[0]: i2c scan: found device @ 0x88  [cx25837]
cx23885[0]: i2c scan: found device @ 0x98  [???]

i2c detect

Output of i2cdetect -l:

i2c-0   i2c             cx23885[0]                              I2C adapter
i2c-1   i2c             cx23885[0]                              I2C adapter
i2c-2   i2c             cx23885[0]                              I2C adapter<pre>

Output of <code>i2cdetect 0</code>:

<pre>WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-0.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

Output of i2cdetect 1:

WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-1.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- 61 -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

Output of i2cdetect 2:

WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-2.
I will probe address range 0x03-0x77.
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- --
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
30: 30 31 32 33 34 35 36 37 -- -- -- -- -- -- -- --
40: -- -- -- -- 44 -- -- -- -- -- -- -- 4c -- -- --
50: 50 51 52 53 54 55 56 57 58 59 5a 5b 5c 5d 5e 5f
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
70: -- -- -- -- -- -- -- --

i2c dump

Output of i2cdump 0 0x50:

No size specified (using byte-data access)
WARNING! This program can confuse your I2C bus, cause data loss and worse!
I will probe file /dev/i2c-0, address 0x50, mode byte
Continue? [Y/n] y
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f    0123456789abcdef
00: 2c 00 05 00 5b 18 00 e8 ff ff ff ff ff ff ff ff    ,.?.[?.?........
10: 18 03 05 00 0d c0 09 03 08 00 18 83 00 00 03 28    ???.?????.??..?(
20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
40: ff 1a 12 c2 86 1e ff ff ff ff ff ff c6 ff ff ff    .?????......?...
50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................

External Links

Compro VideoMate E600F: Difference between revisions

Revision as of 17:27, 29 September 2008

Contents

Overview/Features

Components Used

Other images

Identification

lspci

dmesg

i2c scan

i2c detect

i2c dump

External Links

Navigation menu

Compro VideoMate E600F: Difference between revisions

Revision as of 17:27, 29 September 2008

Overview/Features

Components Used

Other images

Identification

lspci

dmesg

i2c scan

i2c detect

i2c dump

External Links

Navigation menu

Search