Leadtek WinFast DTV2000DS: Difference between revisions
No edit summary |
|||
| Line 268: | Line 268: | ||
http://linuxtv.org/hg/~anttip/af9015/raw-file/6904cb7bd11d/linux/drivers/media/dvb/frontends/af9013_priv.h |
http://linuxtv.org/hg/~anttip/af9015/raw-file/6904cb7bd11d/linux/drivers/media/dvb/frontends/af9013_priv.h |
||
Ensure you activate the firmware as per cloggys instructions below. |
|||
===Frequent lockups during live TV and recording of TV shows=== |
===Frequent lockups during live TV and recording of TV shows=== |
||
Revision as of 11:11, 24 January 2011
A dual tuner DVB-T PCI card from Leadtek.
Currently supported by recent V4L-DVB (as at Sep 2010) The card is not working out of the box, however there is a solution (patch to V4L really).
Your mileage may vary. There are still some issues in using this card; please read on.
Overview/Features
Formats:
- DVB-T
Inputs:
- RF
- Infrared
Components Used
Contains
- NXP TDA18211
Identification
Output of lsusb -v:
Bus 002 Device 002: ID 0413:6a04 Leadtek Research, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0413 Leadtek Research, Inc.
idProduct 0x6a04
bcdDevice 2.00
iManufacturer 1 Afatech
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 46
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Making it work in Ubuntu
Updated 20 Nov 2010 by AMX.
Here is a simple HOWTO/Workaround to get this card working . This is based on debian flavours. Although there are some people that have come up with shell scrips and patches to get something similar, it is better that everyone knows how things are done, and also hopefully this will be incorporated into the new releases of V4L. Until then we all have to sweat it a bit!!
The real solution is based on the bug found in http://www.xpmediacentre.com.au/community/tuners/41937-leadtek-dtv2000ds-4.html . There is another issue that better get fixed and it is to do with I2C byte write numbers.
Please leave comments in the discussion session or put comments in http://www.xpmediacentre.com.au/community/tuners/41937-leadtek-dtv2000ds-4.html so that we keep this updated.
1- Starting from a clean install of 10.04 or 10.10, perform the initial steps to install V4L drivers
sudo apt-get install mercurial linux-headers-$(uname -r) build-essential
2- go to http://linuxtv.org/hg/v4l-dvb/rev/abd3aac6644e and click on the "bz2" link and download the file.
Note: Here I am referring to a specific tag of the repository, i.e. abd3aac6644e. If you have recent kernels such as 2.6.36, you may need to grab the latest source rather than this particular tag. The rest of the process is still the same.
3- run
bzcat v4l-dvb-abd3aac6644e.tar.bz2 | tar xv
cd v4l-dvb-abd3aac6644e
This should create a directory called v4l-dvb-abd3aac6644e
4- Do the following modifications
4.1- The small_i2c fix: This fix is from discussions here http://www.spinics.net/lists/linux-usb/msg37741.html .
Edit the file linux/drivers/media/dvb/dvb-usb/af9015.c and replace
static struct tda18271_config af9015_tda18271_config = {
.gate = TDA18271_GATE_DIGITAL,
.small_i2c = 1,
};
with
static struct tda18271_config af9015_tda18271_config = {
.gate = TDA18271_GATE_DIGITAL,
.small_i2c = TDA18271_16_BYTE_CHUNK_INIT,
};
Then edit the file linux/drivers/media/common/tuners/tda18271.h
and replace
enum tda18271_small_i2c {
TDA18271_39_BYTE_CHUNK_INIT = 0,
TDA18271_16_BYTE_CHUNK_INIT = 1,
TDA18271_08_BYTE_CHUNK_INIT = 2,
};
with
enum tda18271_small_i2c {
TDA18271_39_BYTE_CHUNK_INIT = 0,
TDA18271_16_BYTE_CHUNK_INIT = 16,
TDA18271_08_BYTE_CHUNK_INIT = 8,
TDA18271_03_BYTE_CHUNK_INIT = 3,
};
4.2- The main and the nasty bug i.e. the if_sample_freq bug: This fix is from http://www.xpmediacentre.com.au/community/tuners/41937-leadtek-dtv2000ds-4.html .
If you have a quick look inside the file (just out of interest), you will notice that how this bug was messing up all the tuner frequency calculations. The frequencies are given in Table 41 in the datasheet (http://www.nxp.com/documents/data_sheet/TDA18211HD.pdf)
Anyway
edit the file linux/drivers/media/dvb/frontends/af9013.c
and replace
/* TDA18271 uses different sampling freq for every bw */
if (state->config.tuner == AF9013_TUNER_TDA18271) {
switch (bw) {
case BANDWIDTH_6_MHZ:
if_sample_freq = 3300000; /* 3.3 MHz */
break;
case BANDWIDTH_7_MHZ:
if_sample_freq = 3800000; /* 3.8 MHz */
break;
case BANDWIDTH_8_MHZ:
default:
if_sample_freq = 4300000; /* 4.3 MHz */
break;
}
}
with
/* TDA18271 uses different sampling freq for every bw */
if (state->config.tuner == AF9013_TUNER_TDA18271) {
switch (bw) {
case BANDWIDTH_6_MHZ:
if_sample_freq = 3300000; /* 3.3 MHz */
break;
case BANDWIDTH_7_MHZ:
if_sample_freq = 3500000; /* 3.5 MHz */
break;
case BANDWIDTH_8_MHZ:
default:
if_sample_freq = 4000000; /* 4.0 MHz */
break;
}
}
5- Compile and install the drivers
make sure you are back in the v4l-dvb-abd3aac6644e directory
make config
sed -i -e "s/FIREDTV=m/FIREDTV=n/" v4l/.config
make
sudo make install
wget http://palosaari.fi/linux/v4l-dvb/firmware/af9015/5.1.0.0/dvb-usb-af9015.fw
sudo cp dvb-usb-af9015.fw /lib/firmware
6- Shutdown (you have to shutdown)
7- Startup
8- Hopefully now your tuner is recognized and works happily. If not, double check the process, check for errors that might have been missed, and if it all fails, post to a forum.
Fix for the 5.1 Firmware
[Comments added by Ross] As per the notes added by Cloggy below the 5.1 firmware causes issues if you just follow the guide above. However there is a patch missing which enables support :) This is based on the following commit: http://linuxtv.org/hg/~anttip/af9015/rev/6904cb7bd11d
Replace linux/drivers/media/dvb/frontends/af9013_priv.h with the following file:
Frequent lockups during live TV and recording of TV shows
[Comments added by Cloggy - based on Mythbuntu 10.10] Using the firmware mentioned above (5.1.0.0) on my system resulted in frequent lockups during recording or watching live TV. Mythbackend.log has entries "Poll giving up", "Device error detected" and "Stream handler died unexpectedly". The previous firmware version is more stable. To use the previous version replace the "wget" line in step 5 with:
wget http://palosaari.fi/linux/v4l-dvb/firmware/af9015/4.95.0.0/dvb-usb-af9015.fw
Remember to do a cold boot afterwards to activate this firmware, /var/log/messages should show "af9013: firmware version:4.95.0"
Remote Control Support
I (Gregoryo) have had no success with the remote, but there is hope from dmesg:
[ 22.263721] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:0e.0/0000:02:0a.2/usb2/2-1/input/input5
user@host:~$ cat /proc/bus/input/devices
I: Bus=0003 Vendor=0413 Product=6a04 Version=0200
N: Name="IR-receiver inside an USB DVB receiver"
P: Phys=usb-0000:02:0a.2-1/ir0
S: Sysfs=/devices/pci0000:00/0000:00:0e.0/0000:02:0a.2/usb2/2-1/input/input5
U: Uniq=
H: Handlers=kbd event5
B: EV=3
B: KEY=108fc310 2802891 0 0 0 0 118000 200180 4803 e1680 0 100000 ffe
So I've been using /dev/input/event5 in my tests. I have tried using evtest, mode2, and irw to no avail. I get no indication of any signal coming from the remote. Am I missing a kernel driver module?
Remote Control Support (2)
[Comments added by Cloggy - based on Mythbuntu 10.10] Here my config files to get the remote control (part number y04g0051) working:
/etc/udev/rules.d/20-mythtv.rules:
# /etc/udev/rules.d/20-mythtv.rules
# Leadtek DTV2000DS Remote Control
KERNELS=="2-1",ATTRS{idVendor}=="0413",ATTRS{idProduct}=="6a04",SYMLINK+="input/dtv2000ds_remote"
/etc/lirc/hardware.conf:
# /etc/lirc/hardware.conf REMOTE="Leadtek dtv2000ds y04g0051" REMOTE_MODULES="" REMOTE_DRIVER="devinput" REMOTE_DEVICE="/dev/input/dtv2000ds_remote" REMOTE_LIRCD_CONF="/etc/lirc/lircd.conf" REMOTE_LIRCD_ARGS="" #Chosen IR Transmitter TRANSMITTER="None" TRANSMITTER_MODULES="" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" #Enable lircd START_LIRCD="true" #Don't start lircmd even if there seems to be a good config file #START_LIRCMD="false" #Try to load appropriate kernel modules LOAD_MODULES="true" # Default configuration files for your hardware if any LIRCMD_CONF="" #Forcing noninteractive reconfiguration #If lirc is to be reconfigured by an external application #that doesn't have a debconf frontend available, the noninteractive #frontend can be invoked and set to parse REMOTE and TRANSMITTER #It will then populate all other variables without any user input #If you would like to configure lirc via standard methods, be sure #to leave this set to "false" FORCE_NONINTERACTIVE_RECONFIGURATION="true" START_LIRCMD="true"
/etc/lirc/lircd.conf:
# /etc/lirc/lircd.conf
# brand: Leadtek
# model no. of remote control: Y04G0051
# devices being controlled by this remote: DTV2000DS
begin remote
name Y04G0051
bits 16
eps 30
aeps 100
one 0 0
zero 0 0
gap 263992
pre_data_bits 16
pre_data 0x8001
begin codes
TV 0x00179
PREVIOUS 0x000A8
PLAYPAUSE 0x000CF
NEXT 0x000D0
CLOCK 0x00167
BACK 0x0019C
STOP 0x00080
FORWARD 0x00197
RECORD 0x000A7
ZERO 0X0000B
ONE 0x00002
TWO 0x00003
THREE 0x00004
FOUR 0x00005
FIVE 0x00006
SIX 0x00007
SEVEN 0x00008
EIGHT 0x00009
NINE 0x0000A
EPG 0x0016D
FULLSCREEN 0x00177
RECALL 0x00081
DOT 0x00034
OKINFO 0x00160
SNAPSHOT 0x000D4
MENU 0X0008B
EXIT 0x00080
MUTE 0x00071
SLEEP 0x0008E
UP 0X00067
DOWN 0x0006C
LEFT 0x00069
RIGHT 0x0006A
OK 0X00160
VOL+ 0x00073
VOL- 0x00072
CH+ 0x00192
CH- 0X00193
AUDIO 0x00188
VIDEO 0x00189
RED 0x0018E
GREEN 0X0018F
YELLOW 0x00190
BLUE 0x00191
TELETEXT 0x00184
UNKNOWN1 0X0016B
PIP 0x000B5
DELETE 0x00001
end codes
end remote
Not every single button works yet (most notably the MCE button, but I suspect it needs a different "pre_data" which is probably a generic Windows MCE one.