AVerMedia AVerTV DVB-S Pro (A700): Difference between revisions
Jump to navigation
Jump to search
(added lspci output) |
(Added dmesg output) |
||
Line 16: | Line 16: | ||
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) |
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) |
||
Status: D0 PME-Enable- DSel=0 DScale=3 PME- |
Status: D0 PME-Enable- DSel=0 DScale=3 PME- |
||
</pre> |
|||
* dmesg output of modprobe saa7134 i2c_scan=1: |
|||
<pre> |
|||
Linux video capture interface: v2.00 |
|||
saa7130/34: v4l2 driver version 0.2.14 loaded |
|||
saa7133[0]: found at 0000:00:0b.0, rev: 209, irq: 22, latency: 32, mmio: 0xdfffb800 |
|||
saa7133[0]: subsystem: 1461:a7a1, board: UNKNOWN/GENERIC [card=0,autodetected] |
|||
saa7133[0]: board init: gpio is a600 |
|||
Device driver i2c-3 lacks bus and class support for being resumed. |
|||
saa7133[0]: i2c eeprom 00: 61 14 a1 a7 ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |
|||
saa7133[0]: i2c scan: found device @ 0x1c [???] |
|||
saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] |
|||
Device driver video0 lacks bus and class support for being resumed. |
|||
saa7133[0]: registered device video0 [v4l2] |
|||
Device driver vbi0 lacks bus and class support for being resumed. |
|||
saa7133[0]: registered device vbi0 |
|||
</pre> |
</pre> |
||
Revision as of 15:15, 2 November 2007
An DVB-S PCI card from AVerMedia.
It is currently unsupported under Linux.
Overview
- lspci -vvnn output looks like this:
00:0b.0 Multimedia controller [0480]: Philips Semiconductors SAA7133/SAA7135 Video Broadcast Decoder [1131:7133] (rev d1) Subsystem: Avermedia Technologies Inc Unknown device [1461:a7a1] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (63750ns min, 63750ns max) Interrupt: pin A routed to IRQ 22 Region 0: Memory at dfffb800 (32-bit, non-prefetchable) [size=2K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=3 PME-
- dmesg output of modprobe saa7134 i2c_scan=1:
Linux video capture interface: v2.00 saa7130/34: v4l2 driver version 0.2.14 loaded saa7133[0]: found at 0000:00:0b.0, rev: 209, irq: 22, latency: 32, mmio: 0xdfffb800 saa7133[0]: subsystem: 1461:a7a1, board: UNKNOWN/GENERIC [card=0,autodetected] saa7133[0]: board init: gpio is a600 Device driver i2c-3 lacks bus and class support for being resumed. saa7133[0]: i2c eeprom 00: 61 14 a1 a7 ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[0]: i2c scan: found device @ 0x1c [???] saa7133[0]: i2c scan: found device @ 0xa0 [eeprom] Device driver video0 lacks bus and class support for being resumed. saa7133[0]: registered device video0 [v4l2] Device driver vbi0 lacks bus and class support for being resumed. saa7133[0]: registered device vbi0
Components Used
Driver Development Status
Needed: I2C sniff while tuning with working driver. GPIO Setting of windows driver (when tuning is on and off).