KWorld ATSC 120: Difference between revisions
| Line 92: | Line 92: | ||
* Once your machine comes back up, do an lsmod and verify that the modules did ''not'' load. |
* Once your machine comes back up, do an lsmod and verify that the modules did ''not'' load. |
||
* To make |
* To make digital/ATSC the default, set up the new modules to be loaded explicitly (note the "exit 0" is probably already in the file): |
||
# nano /etc/rc.local |
# nano /etc/rc.local |
||
| Line 100: | Line 100: | ||
exit 0 |
exit 0 |
||
If you want to default to |
If you want to default to analog mode instead, replace "cx88-dvb" above with "cx8800". |
||
* MythTV users: You will need to ensure that the MythTV backend starts '''after''' the drivers are loaded. This can usually be done by adding to or altering one or more of your distribution's startup scripts. If you have not already done so, you must add both the dummy "MythTV" user and the user you plan to run mythfrontend from (e.g. your primary user account) to the "video" and "audio" groups, and put yourself into the "MythTV" group as well. |
* MythTV users: You will need to ensure that the MythTV backend starts '''after''' the drivers are loaded. This can usually be done by adding to or altering one or more of your distribution's startup scripts. If you have not already done so, you must add both the dummy "MythTV" user and the user you plan to run mythfrontend from (e.g. your primary user account) to the "video" and "audio" groups, and put yourself into the "MythTV" group as well. |
||
Revision as of 19:39, 24 July 2008
The Kworld ATSC 120, also known as the KWorld PlusTV HD PCI 120, is an ATSC PCI add-in card which can receive standard analog television signals (NTSC, PAL, possibly others), as well as standard and high definition digital ATSC broadcasts up to 1920x1080 interlaced. The ATSC 120 features composite and s-video inputs on the back, an analog FM radio, and an infrared remote control. Television audio may be received via an internal PCI/DMA device that is handled by ALSA (e.g. as /dev/dsp1), and via a line-out connector on the back of the card.
This device is identical to the Geniatech HDTV Thriller X8000A.
Note: This article is a work in progress.
Status
As of 27 Mar 2008, this card can be used in both analog and digital ATSC modes, although this must be done separately as a reboot between mode switches is presently required, due to the architecture of the card and a resource conflict in the driver. A solution to this issue is currently being worked on. The FM radio, composite video, and S-Video inputs all work when the card is initialized into analog mode. The remote control is not currently supported in any mode, yet.
Experimental drivers can be had by fetching revision 7448 or later of the main v4l-dvb repository.
PCI Information
The ATSC 120 has a PCI subsytem ID of 17de:08c1. The complete details of this card, as reported by lspci -vvnn are:
00:05.0 Multimedia video controller [0400]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Unknown device [17de:08c1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 13750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.1 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8801] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Unknown device [17de:08c1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.2 Multimedia controller [0480]: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev 05)
Subsystem: KWorld Computer Co. Ltd. Unknown device [17de:08c1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1500ns min, 22000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Major components used
- Xceive XC3028 (tuner & analog IF demodulator)
- Samsung S5H1409 / Conexant CX24227 (digital demodulator)
- Conexant cx2388x (A/V Decoder & PCI bridge)
Making it Work
The ATSC 120 is a fairly routine card to set up. Although there is currently is a resource conflict that prevents easy switching between ATSC and analog modes, selecting the desired default mode is accomplished by loading the proper module after a reboot, as described below.
Step by Step
Note: Distribution support for the ATSC 120 is unclear, however, the drivers are currently part of the v4l-dvb staging repository, and thus in line to be included with the kernel at some point in the near future. When that happens, some of these steps may no longer be necessary.
- Ensure that there are no conflicting drivers being built with your kernel, either as modules or built-in. Basically, disable the whole video4linux subsystem from your kernel config. Rebuild, re-install, and reboot if necessary.
- Acquire the xc3028 firmware file and place it in /lib/modules , as directed by the XC3028/2028 info page here on the LinuxTV wiki.
- Acquire Mercurial from your distribution's packaging system and install it.
- Acquire the v4l-dvb repository from linuxtv.org, build and install it:
# hg clone http://linuxtv.org/hg/v4l-dvb # cd v4l-dvb # make # make install
- Create a new file to blacklist the new modules from being auto-loaded:
# nano /etc/modprobe.d/blacklist-misc
Add these four lines to it:
blacklist cx8800 blacklist cx8802 blacklist cx88-alsa blacklist cx88-dvb
Note: Some Debian systems will have trouble the blacklist, as the modules may refuse to load at all, even manually.
- Save the file and reboot.
- Once your machine comes back up, do an lsmod and verify that the modules did not load.
- To make digital/ATSC the default, set up the new modules to be loaded explicitly (note the "exit 0" is probably already in the file):
# nano /etc/rc.local
modprobe cx88-dvb modprobe cx88-alsa exit 0
If you want to default to analog mode instead, replace "cx88-dvb" above with "cx8800".
- MythTV users: You will need to ensure that the MythTV backend starts after the drivers are loaded. This can usually be done by adding to or altering one or more of your distribution's startup scripts. If you have not already done so, you must add both the dummy "MythTV" user and the user you plan to run mythfrontend from (e.g. your primary user account) to the "video" and "audio" groups, and put yourself into the "MythTV" group as well.
- If your computer has already loaded a set of modules from your stock kernel, you will need to reboot your computer now to make all of these changes take effect. When the modules are loaded, the ATSC 120 will be auto-detected, but removing the existing modules will not necessarily reset the state of the capture card, due to the aforementioned resource conflict.