ASUS My Cinema-P7131 Hybrid
A PCI DVB-T card from ASUS.
The analog part of this card works out of the box.
Not sure if it is exactly the same card as the ASUS P7131 Dual.
Overview/Features
- PCI
- RF formats: PAL, DVB-T
The card does not have an AD for sound.
Card connectors
- RF signal: Two IEC connectors
- Video Input: S-Video mini-DIN
- IR-Remote: 2.5mm jack
- Audio output: Card internal
The RF inputs are for:
- PAL TV RF signal
- DVB-T RF signal
- FM radio RF signal
The original documentation says:
Upper IEC connector is marked "RF/FM-IN" and is for FM radio and DVB-T
Lower IEC connector is marked "CATV-IN" and is for PAL TV
The FM radio is fixed to the upper connector, but for TV (PAL and DVB-T) the connectors can apparently be controlled by software. This is TBD. ???
- note: In several cases users had to connect their antenna to the analog plug for dvb-t!
- note: Signal association can change after booting into Windows and using bundled Win32 software to control card. Best solution is to split antenna signal and attach to both connectors.
Components Used
- TV tuner: tda8290+75
- Analog demodulator: ??
- FM radio chip: ??
- tda10046 demodulator
- Video/audio decoder: Philips Semiconductors SAA7133 Video Broadcast Decoder (rev d1)
Identification
#lspci -vvv -nn
05:01.0 Multimedia controller [0480]: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder [1131:7133] (rev d1)
Subsystem: ASUSTeK Computer Inc. Device [1043:4876]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Making it Work
Firmware
This card requires a firmware file (dvb-fe-tda10046.fw) for the DVB-T demodulator. This file can be obtained two different ways:
- download a package containing this and many other firmwares:
- DVB firmwares v2, 7Z–728 KiB, TBZ–1.80 MiB, or ZIP–2.08 MiB, contains 114 files.
- DVB firmwares v1 (deprecated) 7Z–454 KiB, TBZ–1.32 MiB, or ZIP–1.53 MiB, 36 files.
- using the get_dvb_firmware perl script, included with kernel sources, which will download the Windows driver file and rip the firmware out of it:
cd /[kernel source directory]/Documentation/dvb/
perl get_dvb_firmware tda10046
Kernel source directory will usually be /usr/src/linux/. Whatever method you choose, once the download is complete, place a copy of the firmware file in your /lib/firmware directory. (This directory may differ with some distros i.e.depending on your hotplug version it could be /usr/lib/hotplug/firmware/ ; consult your distro's documentation for the appropriate location):
sudo cp dvb-fe-tda10046.fw /lib/firmware
(replace /lib/firmware with /usr/lib/hotplug/firmware/ if required)
Bugs
This is not tested yet:
Get firmware, old option
In /usr/src/linux/drivers/media/video/saa7134/saa7134-dvb.c, line 873, struct tda1004x_config philips_tiger_config change the entry
.request_firmware = NULL
to
.request_firmware = philips_tu1216_request_firmware
Run /usr/src/linux/Documentation/dvb/get_dvb_firmware and copy the dvb-fe-tda10046.fw to /lib/firmware
modprobe saa7134 card=78 gpio_tracking=1
See http://www.spinics.net/lists/vfl/msg27672.html
Get firmware, new option
The Mercurial version "emerge v4l-dvb-hg" gives the card a proper card number of 112. The card can then be brought up with
modprobe saa7134 card=112 tuner=54 gpio_tracking=1 i2c_scan=1
You may also need to
modprobe saa7134-dvb modprobe saa7134-alsa
This works now but may not continue to do so.
Drivers
Module Options: For analog signal (autodetected?):
saa7134 card=112 tuner=54
(it used to say card=78, but that's the ASUS P7131-dual, not the -hybrid. I'm not yet sure if tuner=54 works -- REW)
module saa7134 was loaded automatically, but in addition command "modprobe saa7134_dvb" was required. Only after this the directory /dev/dvb appeared.
Sample kernel output
From Gentoo linux kernel 2.6.28-r2 (as second PCI card):
saa7134 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 saa7133[1]: found at 0000:04:02.0, rev: 209, irq: 18, latency: 32, mmio: 0xe3004800 saa7133[1]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid [card=112,autodetected] saa7133[1]: board init: gpio is 0 input: saa7134 IR (ASUSTeK P7131 Hybri as /class/input/input6 tuner' 2-004b: chip found @ 0x96 (saa7133[1]) saa7133[1]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7133[1]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff ff saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff ff saa7133[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7133[1]: i2c scan: found device @ 0x10 [???] saa7133[1]: i2c scan: found device @ 0x96 [???] saa7133[1]: i2c scan: found device @ 0xa0 [eeprom] tda829x 2-004b: setting tuner address to 61 tda829x 2-004b: type set to tda8290+75a saa7133[1]: registered device video1 [v4l2] saa7133[1]: registered device vbi1 saa7133[1]: registered device radio1
Remote control support
An IR remote control is supplied. There is a sensor cable that must be plugged into the card.
The remote requires Linux 2.6.22
Also See
- http://gentoo-wiki.com/HARDWARE_saa7134 (Generic)
- http://www.mail-archive.com/linux-dvb@linuxtv.org/msg22647.html (Remote control)
- http://gentoo-wiki.com/Saa7134_quick_guide
- http://www.thadathil.net/dvb/fw/ (Firmware repository)
- Supported saa713x devices
- Saa713x devices: Generic SAA7134 Card Installation
Discussions:
- http://archives.devshed.com/forums/linux-97/dvb-t-on-asustek-p7131-dual-device-4876t-1966310.html
- http://ubuntuforums.org/showthread.php?t=195686 (Someone who successfully have used the card)
Old discussions (may no longer be relevant):
- http://www.mail-archive.com/linux-dvb@linuxtv.org/msg19973.html (Thread discussing driver development)
- http://www.mail-archive.com/linux-dvb@linuxtv.org/msg19579.html
- http://www.spinics.net/lists/vfl/msg27672.html