Hauppauge WinTV-NOVA-HD-S2
DVB-S/S2 PCI card. Similar to the HVR-4000 but without DVB-T or analogue TV features.
Product page: http://www.hauppauge.co.uk/site/products/data_novahds2.html .
The card is supported in the stock Linux kernel since version 2.6.28, so ideally you should simply use 2.6.28 or later, and obtain and install the latest firmware as described here: Hauppauge_WinTV-HVR-4000. The right modules should be loaded automatically on boot (check lsmod and dmesg output). Then start Kaffeine 0.8.8 for example.
If you have to run an earlier kernel try the v4l-dvb repository at http://linuxtv.org/hg/v4l-dvb, and see Hauppauge_WinTV-HVR-4000 or the link below for getting the latest firmware. It is identified as "Hauppauge WinTV-HVR4000(Lite) DVB-S/S2".
hg clone http://linuxtv.org/hg/v4l-dvb cd v4l-dvb make sudo make install sudo reboot
Resources
- An old ubuntuusers.de forum thread with how-to on page 3 in German (should be easily machine-translateable), which seems to work for some people. Uses driver code, which used to be in the linuxtv Hg repository, with some updates to that code back then so that the HD-S2 code works with newer kernels. Recognized as a "Hauppauge WinTV HVR-4000(Lite)". (Wonder why that code was removed.)
Sample kernel output
Note that this differs slightly from the HVR-4000 model in that there are no analogue sound inputs on the card. This results in the following line in the kernel log: tveeprom 0-0050: audio processor is None (idx 0)
Linux video capture interface: v2.00 cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded cx88[0]: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69,autodetected], frontend(s): 1 cx88[0]: TV tuner type -1, Radio tuner type -1 cx88/0: cx2388x v4l2 driver version 0.0.6 loaded cx2388x alsa driver version 0.0.6 loaded tveeprom 0-0050: Hauppauge model 69100, rev B2C3, serial# 28987XX tveeprom 0-0050: MAC address is 00-0D-FE-2C-3B-XX tveeprom 0-0050: tuner model is Conexant CX24118A (idx 123, type 4) tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80) tveeprom 0-0050: audio processor is None (idx 0) tveeprom 0-0050: decoder processor is CX882 (idx 25) tveeprom 0-0050: has no radio, has IR receiver, has no IR transmitter cx88[0]: hauppauge eeprom: model=69100 input: cx88 IR (Hauppauge WinTV-HVR400 as /class/input/input4 cx88[0]/2: cx2388x 8802 Driver Manager ... SNIP (lines removed) ... cx88[0]/2: found at 0000:01:06.2, rev: 5, irq: 17, latency: 32, mmio: 0xe5000000 cx8802_probe() allocating 1 frontend(s) ... SNIP (lines removed) ... cx88[0]/0: found at 0000:01:06.0, rev: 5, irq: 17, latency: 32, mmio: 0xe3000000 cx88[0]/0: registered device video0 [v4l2] cx88[0]/0: registered device vbi0 ... SNIP (lines removed) ... cx88/2: cx2388x dvb driver version 0.0.6 loaded cx88/2: registering cx8802 driver, type: dvb access: shared cx88[0]/2: subsystem: 0070:6906, board: Hauppauge WinTV-HVR4000(Lite) DVB-S/S2 [card=69] cx88[0]/2: cx2388x based DVB/ATSC card ... SNIP (lines removed) ... cx88[0]/1: CX88x/0: ALSA support for cx2388x boards DVB: registering new adapter (cx88[0]) DVB: registering adapter 0 frontend 0 (Conexant CX24116/CX24118)... ... SNIP (lines removed) ... cx24116_firmware_ondemand: Waiting for firmware upload (dvb-fe-cx24116.fw)... firmware: requesting dvb-fe-cx24116.fw cx24116_firmware_ondemand: Waiting for firmware upload(2)... cx24116_load_firmware: FW version 1.22.82.0 cx24116_firmware_ondemand: Firmware upload complete