AVerMedia AVerTV Hybrid Speedy PCI-E

From LinuxTVWiki
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
An AVerMedia AVerTV Hybrid Speedy PCI-E


This article is a stub or is incomplete.
This article requires expansion. Please help add informative information if you can.


The AVerMedia AVerTV Hybrid Speedy PCI-E (H788R) is a PCIe analog and DVB-T device from AVerMedia. It is currently unsupported under Linux.

Overview/features

Components used

  • TDA18271HDC1
  • Intel WJCE6353
  • NXP SAA7136E/1/G
  • PCI-E bridge NXP SAA7160ET

Images

Identification

#lspci
03:00.0 0480: 1131:7160 (rev 03)
       Subsystem: 1461:1455    
       Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx- 
       Latency: 0, Cache Line Size: 32 bytes                                                                
       Interrupt: pin A routed to IRQ 17                                                                    
       Region 0: Memory at ea100000 (64-bit, non-prefetchable) [size=1M]                                    
       Capabilities: [40] Message Signalled Interrupts: Mask- 64bit+ Count=1/32 Enable-                     
               Address: 0000000000000000  Data: 0000                                                        
       Capabilities: [50] Express (v1) Endpoint, MSI 00                                                     
               DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <256ns, L1 <1us                       
                       ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-                                      
               DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-                           
                       RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-                                         
                       MaxPayload 128 bytes, MaxReadReq 128 bytes                                           
               DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr- TransPend-                          
               LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <4us, L1 <64us             
                       ClockPM- Suprise- LLActRep- BwNot-                                                   
               LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-                             
                       ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-                                       
               LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-           
       Capabilities: [74] Power Management version 2                                                        
               Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot-,D3cold-)                   
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-                                                  
       Capabilities: [80] Vendor Specific Information <?>                                                   
       Capabilities: [100] Vendor Specific Information <?>                                                  
       Kernel driver in use: SAA716x Hybrid                                                                 
       Kernel modules: saa716x_hybrid                                  

Making it work

Drivers

Drivers for the bridge interface (saa716x) can be found here. Once installed, the card will be recognized as a DVB device. However, with there being no glue code for the device's frontend, it remains unsupported.

Sample kernel output

#dmesg
SAA716x Hybrid 0000:03:00.0: PCI INT A disabled
SAA716x Hybrid 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
SAA716x Hybrid 0000:03:00.0: setting latency timer to 64
DVB: registering new adapter (SAA716x dvb adapter)