From LinuxTVWiki
Revision as of 08:40, 12 April 2012 by Neilb (talk | contribs)
Jump to: navigation, search


This card is widely available on ebay shipping from China, and looks similar to a TBS QBox II (probably a knockoff), but the hardware is not the same.

Reports are that this is pretty much (or identical) to the DVBSKY S860. DVBHD claim to be affiliated with TeVii however.

Linux drivers provided on the CD are an old (2010) snapshot of the Liplianin tree with the BST patches applied, filename s2-liplianin-8c8997d531c6_BST_0911.zip. This seems to be the basis of the live CD that boots into Chinese HTPC software, but this is too old for modern kernels.

To make this card work (as of Kernel 3.3) you need to apply the patches from DVBSKy's website, which is the "BST" patch-set. Because this card is similar to the S860, these drivers work.

This card does seem to work in Linux, although occasionally locks up the system temporarily in MythTV.


lsusb shows this as:

Bus 001 Device 002: ID 0572:6830 Conexant Systems (Rockwell), Inc.


Markings on the box itself just say "S2 Box", with a bunch of logos.

dmesg (once drivers are installed as above)

[   62.370817] dw2102: su3000_identify_state
[   62.370820] 
[   62.370822] dvb-usb: found a 'Bestunar US6830 HD' in warm state.
[   62.370834] dw2102: su3000_power_ctrl: 1, initialized 0
[   62.370835] 
[   62.372240] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   62.375074] IR RC6 protocol handler initialized
[   62.379162] DVB: registering new adapter (Bestunar US6830 HD)
[   62.385975] IR JVC protocol handler initialized
[   62.388558] leds_ss4200: no LED devices found
[   62.397357] dvb-usb: MAC address: ff:ff:ff:ff:ff:ff
[   62.398236] IR Sony protocol handler initialized
[   62.399325] dw2102: US6830: US6830_frontend_attach!
[   62.399328] 
[   62.410077] IR SANYO protocol handler initialized
[   62.426809] it913x-fe: Tuner LNA type :38
[   62.429599] IR MCE Keyboard/mouse protocol handler initialized
[   62.431792] DS3000 chip version: c0 attached.
[   62.434346] TS202x chip version[1]: 81 attached.
[   62.449923] lirc_dev: IR Remote Control driver registered, major 250 
[   62.452778] IR LIRC bridge handler initialized
[   62.453177] TS202x chip version[2]: 81 attached.
[   62.497344] m88ds3103_load_firmware: Waiting for firmware upload (dvb-fe-ds300x.fw)...
[   62.568053] Registered IR keymap rc-msi-digivox-iii
[   62.568163] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/rc/rc0/input2
[   62.568292] rc0: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4.4/rc/rc0
[   63.181663] m88ds3103_load_firmware: Waiting for firmware upload(2)...
[   64.411620] dw2102: Attached DS3000!
[   64.411624] 
[   64.411659] DVB: registering adapter 1 frontend 0 (Montage DS3103/TS2022)...
[   64.412075] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/input/input3
[   64.412240] dvb-usb: schedule remote query interval to 150 msecs.
[   64.412246] dw2102: su3000_power_ctrl: 0, initialized 1
[   64.412247] 
[   64.412249] dvb-usb: Bestunar US6830 HD successfully initialized and connected.

Kernel modules

  • dw2102
  • m88ds3103 (even though it's a DS3000, the ds3000 module that's in the kernel already seems outdated, and this one from DVBSky is backwards compatible)


  • USB bridge: Conexant Systems ???
  • Demodulator: Montage M88DS3000
  • RF: Montage M88TS2020


  • dvb-fe-ds300x.fw (available from DVBSky's website)


  • Make sure you plug the power in (and get the green light) before connecting the USB, otherwise the DS3000 (Montage) chip won't be found by the driver and you'll be lacking a frontend0

See also