Emtec S830: Difference between revisions

From LinuxTVWiki
Jump to navigation Jump to search
m (Use thumbnails.)
(corrected 2 typos)
Line 13: Line 13:




When i try to tune to a frequency from a channels-file i have from one of my other dvbt cards.. i just gets no lock ...
When i try to tune to a frequency from a channels-file i have from one of my other dvbt cards.. it just gets no lock ...
$ tzap -a 3 -c /home/waldo/Desktop/channels.conf "een"
$ tzap -a 3 -c /home/waldo/Desktop/channels.conf "een"
using '/dev/dvb/adapter3/frontend0' and '/dev/dvb/adapter3/demux0'
using '/dev/dvb/adapter3/frontend0' and '/dev/dvb/adapter3/demux0'
Line 50: Line 50:
[ 184.643047] usbcore: registered new interface driver dvb_usb_dib0700
[ 184.643047] usbcore: registered new interface driver dvb_usb_dib0700


I opened up the stick (see pics below) and checked what was inside; it seems to be the same as what what modules are loaded
I opened up the stick (see pics below) and checked what was inside; it seems to be the same as the modules are loaded, so far so good


==LSUSB Output==
==LSUSB Output==

Revision as of 11:14, 17 December 2007

This is a DVB-T USB Stick with dual tuners, remote control, and 'diversity' tuning capabilities (not sure about the last)

05/12/2007 Not working with v4l-dvb hg on kernel 2.6.22-14

http://www.linuxtv.org/pipermail/linux-dvb/2007-July/019261.html

=> after adding the usbid as described in the patch above I get the exact same result as the user in the mailinglist .. led goes on , modules are loaded, but no lock on frequencies. I also downloaded the firmware , cause i didn't have that yet;

wget http://www.wi-bw.tfh-wildau.de/~pboettch/home/linux-dvb-firmware/dvb-usb-dib0700-1.10.fw
sudo cp dvb-usb-dib0700-1.10.fw /lib/firmware

It should be behaving like a Pinnacle PCTV Dual DVB-T Diversity (PCTV 2000e USB)


When i try to tune to a frequency from a channels-file i have from one of my other dvbt cards.. it just gets no lock ...

$ tzap -a 3 -c /home/waldo/Desktop/channels.conf "een"
using '/dev/dvb/adapter3/frontend0' and '/dev/dvb/adapter3/demux0'
tuning to 482000000 Hz
video pid 0x1011, audio pid 0x1012
status 00 | signal fc25 | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal f1e4 | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal dfe9 | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal e1b9 | snr 0000 | ber 001fffff | unc 00000000 |
status 00 | signal e9cd | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal dcc9 | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal e207 | snr 0000 | ber 001fffff | unc 00000000 |
status 01 | signal db09 | snr 0000 | ber 001fffff | unc 00000000 |


dmesg output after usbid patch

[  183.731819] usb 2-7: new high speed USB device using ehci_hcd and address 3
[  183.798267] usb 2-7: configuration #1 chosen from 1 choice
[  183.880076] dib0700: loaded with support for 5 different device-types
[  183.880182] dvb-usb: found a 'EMTEC S830 TD Stick' in cold state, will try to load a firmware
[  183.903331] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
[  184.008207] dib0700: firmware started successfully.
[  184.259443] dvb-usb: found a 'EMTEC S830 TD Stick' in warm state.
[  184.259497] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  184.259585] DVB: registering new adapter (EMTEC S830 TD Stick)
[  184.378936] DVB: registering frontend 2 (DiBcom 7000PC)...
[  184.400418] MT2266: successfully identified
[  184.482671] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[  184.482792] DVB: registering new adapter (EMTEC S830 TD Stick)
[  184.559678] DVB: registering frontend 3 (DiBcom 7000PC)...
[  184.561611] MT2266: successfully identified
[  184.642628] input: IR-receiver inside an USB DVB receiver as /class/input/input8
[  184.642653] dvb-usb: schedule remote query interval to 150 msecs.
[  184.642658] dvb-usb: EMTEC S830 TD Stick successfully initialized and connected.
[  184.643047] usbcore: registered new interface driver dvb_usb_dib0700

I opened up the stick (see pics below) and checked what was inside; it seems to be the same as the modules are loaded, so far so good

LSUSB Output

Bus 002 Device 007: ID 1164:1e8c YUAN High-Tech Development Co., Ltd Device Descriptor:

 bLength                18
 bDescriptorType         1
 bcdUSB               2.00
 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0
 bMaxPacketSize0        64
 idVendor           0x1164 YUAN High-Tech Development Co., Ltd
 idProduct          0x1e8c
 bcdDevice            1.00
 iManufacturer           1 YUANRD
 iProduct                2 STK7700D
 iSerial                 3 0000000001
 bNumConfigurations      1
 Configuration Descriptor:
   bLength                 9
   bDescriptorType         2
   wTotalLength           46
   bNumInterfaces          1
   bConfigurationValue     1
   iConfiguration          0
   bmAttributes         0xa0
     (Bus Powered)
     Remote Wakeup
   MaxPower              500mA
   Interface Descriptor:
     bLength                 9
     bDescriptorType         4
     bInterfaceNumber        0
     bAlternateSetting       0
     bNumEndpoints           4
     bInterfaceClass       255 Vendor Specific Class
     bInterfaceSubClass      0
     bInterfaceProtocol      0
     iInterface              0
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x01  EP 1 OUT
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               1
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x81  EP 1 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               1
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x82  EP 2 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               1
     Endpoint Descriptor:
       bLength                 7
       bDescriptorType         5
       bEndpointAddress     0x83  EP 3 IN
       bmAttributes            2
         Transfer Type            Bulk
         Synch Type               None
         Usage Type               Data
       wMaxPacketSize     0x0200  1x 512 bytes
       bInterval               1

Device Qualifier (for other device speed):

 bLength                10
 bDescriptorType         6
 bcdUSB               2.00
 bDeviceClass            0 (Defined at Interface level)
 bDeviceSubClass         0
 bDeviceProtocol         0
 bMaxPacketSize0        64
 bNumConfigurations      1

Hardware

Demodulators (2)

DiBcom7000PC1-AXXXa-G
QGYN8

Tuners (2)

MT2266F

Its says PD-870 on the PCB though emtec sells it as S830, so clearly some rebranding is going on

Pics