Re: Routing Probs with dvb0

[Mihai Amariutei <mihai@ambra.ro>]

1. No, is not OK. The sync (signal quality) should be over 63 (128 for a
perfect reception). 3 means no signall at all. Check cables, LNC, dvbd.conf,
etc.
2. EON has 1 PID for unicast (0x200) and two others for multicast, but dvbd
should set them automatically, so no setting in dvbd.conf is necessary.
3. dvbd takes care of that. Just set the external interface used in dvbd.h
(ppp0/eth0/whatever)

----- Original Message -----
From: "Robin Edgar Tripany" <red@tripany.com>
To: "Uwe Guenther" <uwe@cscc.de>; <linux-dvb@linuxtv.org>
Cc: "Christian Berding" <CBerding@Energis.nl>
Sent: Thursday, October 12, 2000 9:34 PM
Subject: Re: Routing Probs with dvb0


> K...... got dvbd drivers compiled, installed and they work :)
>
> got dvbd compiled and dvbd.conf editted to my specific settings....
> my primary questions are:
>
> 1. When i run dvbd without the -q option i get these lines over and over
> again:
>
>     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc = 319
Nest
> = 43264"
>     "VFsync = 0, Freq = 2033000000, Sync = 3 Afc = 4293076671 Agc = 303
Nest
> = 43776"
>
>     is this ok?
> 2. How many filters do i need in /etc/dvbd.conf?
>     (under windows i have 5!!!!)
> 3. how do you set a MAC address on your card?
> 4. as i understand you have to use mrouted to multicast your streams,
>     what are the tunnel settings? (local ip = my uplink device?
remote=???)
>     might you have your mrouted.conf file?
>      I dont really understand the mrouted.conf file :)))
>
>     "phyint dvb0 altnet 212.17.1.212/1 altnet 125.0.0.0/1"
>     "phyint eth0"
>
>     is the first altnet my ppp device and the second one the destination
> address?
>
> well, i hope someone can help me :)
>
> thanx
>
> robin
>
>
> ----- Original Message -----
> From: "Uwe Guenther" <uwe@cscc.de>
> To: "Robin Edgar Tripany" <red@tripany.com>
> Sent: Thursday, October 05, 2000 5:28 PM
> Subject: Re: Routing Probs with dvb0
>
>
> > Robin Edgar Tripany wrote:
> > >
> > > What did you use to get EON working?! where can i find the sources?
> > >
> >
> > http://www.linuxtv.org/download/dvb/siemens_dvb-0.7.1.tar.gz
> > http://www.linuxtv.org/download/dvb/dvbd2.tar.gz
> >
> >  and you could check my config, they is located at
> >
> > http://www.cscc.de/eon.tar.gz
> >
> >
> > ... may the Tux be with you! =Uwe=
> > --
> > Uwe Günther                    \\://                  mailto:uwe@cscc.de
> > Haupstraße 88                  (o -)                  http://www.cscc.de
> > 98631 Behrungen          ---ooO-(_)-Ooo---          tel.:+49.36944.54448
> > Germany                                       Linux, enjoy the ride ...!
> >
>
>