[linux-dvb] Triple packet problem

[KOKO <kcho@slank.com>]

Hi,

I got my dvb-20030119.tar.bz2 working almost fine ;-( 

- make insmod  - ok

dmesg:
Linux video capture interface: v1.00
DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
PCI: Found IRQ 10 for device 00:0d.0
stv0299.c: setup for tuner BSRU6, TDQB-S00x
DVB: registering frontend 0:0 (STV0299/TSA5059/SL1935 based)...

lsmod:
Module                  Size  Used by    Tainted: P
dvb-ttpci             322064   0  (unused)
input                   3072   0  [dvb-ttpci]
ves1820                 3460   0
stv0299                 6232   1
grundig_29504-491       3188   0
grundig_29504-401       3240   0
alps_tdlb7              3724   0
alps_tdmb7              3276   0
alps_bsrv2              3444   0
dvb-core               34180   3  [dvb-ttpci ves1820 stv0299 grundig_29504-491 grundig_29504-401 alps_tdlb7 alps_tdmb7 alps_bsrv2]
videodev                4448   0  [dvb-ttpci]

- dvbtune (-n dpid     Add network interface and receive MPE on PID dpid) - ok
Using DVB card "STV0299/TSA5059/SL1935 based"
tuning DVB-S to L-Band:xxxxxxxxxx, Pol:H Srate=xxxxxxx, 22kHz=on
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_CARRIER
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Bit error rate: 3840
Signal strength: 65535
SNR: 45897
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Successfully opened network device, please configure the dvb interface

- ifconfig dvb0_0 hw ether 00:02:80:01:03:ea <private_ip> up - ok

- route add -net 224.0.0.0 netmask 240.0.0.0 dev dvb0_0 - ok

- my_simple_multicast_receiver_program/mcastreceive <multicast_ip> <multicast_port> - ok
dmesg:
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 2 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 01 02 03
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: no feed to stop

after this, I receive data in perfect condition, except when I unplugged & plugged cable from my dvb card ( > 1 second) then receiving is stop (I have to use dvbtune again w/o -n & then re-run my multicast_program to receive packet) this is not happen when I use dvb-20030529.tar.bz2 even when I unplugged > 15 minute. The problem with this newer driver is I got triple exactly same data for each message sent.
If I just could use dvb-20030119.tar.bz2 but with auto tuning feature like newer driver.....?

TIA.

B'Regards,
KOKO

NB: I use Slackware 8
Linux dvb 2.4.18 #1 Mon Jan 20 02:04:33 WIT 2003 i586 unknown


dvb-20030529 detail:
- make insmod  - ok
dmesg:
Linux video capture interface: v1.00
DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
PCI: Found IRQ 10 for device 00:0d.0
stv0299.c: setup for tuner BSRU6, TDQB-S00x
DVB: registering frontend 0:0 (STV0299/TSA5059/SL1935 based)...

lsmod:
Module                  Size  Used by    Tainted: P
dvb-ttpci             297108   0  (unused)
input                   3072   0  [dvb-ttpci]
ves1820                 3780   0
stv0299                 6488   0  (unused)
grundig_29504-491       3188   0
grundig_29504-401       3528   0
alps_tdlb7              3724   0
alps_tdmb7              3276   0
alps_bsrv2              3444   0
dvb-core               35044   3  [dvb-ttpci ves1820 stv0299 grundig_29504-491 grundig_29504-401 alps_tdlb7 alps_tdmb7 alps_bsrv2]
videodev                4448   0  [dvb-ttpci]

- dvbtune (-n dpid     Add network interface and receive MPE on PID dpid) - ok
Using DVB card "STV0299/TSA5059/SL1935 based"
tuning DVB-S to L-Band:1073903768, Pol:H Srate=2540000, 22kHz=on
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_CARRIER
polling....
Getting frontend event
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Bit error rate: 62976
Signal strength: 65535
SNR: 49836
FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
Successfully opened network device, please configure the dvb interface

- ifconfig dvb0_0 hw ether 00:02:80:01:03:ea <private_ip> up - ok

- route add -net 224.0.0.0 netmask 240.0.0.0 dev dvb0_0 - ok

- my_simple_multicast_receiver_program/mcastreceive <multicast_ip> <multicast_port> - ok
dmesg:
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 2 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 01 02 03
dvb0_0: filter mac=01 00 5e 00 00 01
dvb0_0: set_mc_list, 1 entries
dvb0_0: filter mac=00 02 80 01 03 ea
dvb0_0: filter mac=01 00 5e 00 00 01 




-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.