[linux-dvb] Re: Triple packet problem (getting worse)

[Andaka Wahyu Adi <kcho@slank.com>]

I got the same problem below using http://linuxtv.org/download/dvb/linuxtv-dvb-1.0.0-pre3.tar.gz
Even worse (4 to 5 same packet for each packet sent)
But I'm quiet sure this is not my "Simple Multicast receiver using UNIX sockets program", I'll send you the source if needed.
Please help.
Thanks.

B'Rgrds,
Andaka Wahyu Adi


At 04:36 PM 6/2/2003 +0700, KOKO wrote:

>Hi,
>
>I got my dvb-20030119.tar.bz2 working almost fine ;-( 
>
>- make insmod  - ok
>
>dmesg:
>Linux video capture interface: v1.00
>DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
>PCI: Found IRQ 10 for device 00:0d.0
>stv0299.c: setup for tuner BSRU6, TDQB-S00x
>DVB: registering frontend 0:0 (STV0299/TSA5059/SL1935 based)...
>
>lsmod:
>Module                  Size  Used by    Tainted: P
>dvb-ttpci             322064   0  (unused)
>input                   3072   0  [dvb-ttpci]
>ves1820                 3460   0
>stv0299                 6232   1
>grundig_29504-491       3188   0
>grundig_29504-401       3240   0
>alps_tdlb7              3724   0
>alps_tdmb7              3276   0
>alps_bsrv2              3444   0
>dvb-core               34180   3  [dvb-ttpci ves1820 stv0299 grundig_29504-491 grundig_29504-401 alps_tdlb7 alps_tdmb7 alps_bsrv2]
>videodev                4448   0  [dvb-ttpci]
>
>- dvbtune (-n dpid     Add network interface and receive MPE on PID dpid) - ok
>Using DVB card "STV0299/TSA5059/SL1935 based"
>tuning DVB-S to L-Band:xxxxxxxxxx, Pol:H Srate=xxxxxxx, 22kHz=on
>polling....
>Getting frontend event
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_CARRIER
>polling....
>Getting frontend event
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
>Bit error rate: 3840
>Signal strength: 65535
>SNR: 45897
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
>Successfully opened network device, please configure the dvb interface
>
>- ifconfig dvb0_0 hw ether 00:02:80:01:03:ea <private_ip> up - ok
>
>- route add -net 224.0.0.0 netmask 240.0.0.0 dev dvb0_0 - ok
>
>- my_simple_multicast_receiver_program/mcastreceive <multicast_ip> <multicast_port> - ok
>dmesg:
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 2 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 01 02 03
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: no feed to stop
>
>after this, I receive data in perfect condition, except when I unplugged & plugged cable from my dvb card ( > 1 second) then receiving is stop (I have to use dvbtune again w/o -n & then re-run my multicast_program to receive packet) this is not happen when I use dvb-20030529.tar.bz2 even when I unplugged > 15 minute. The problem with this newer driver is I got triple exactly same data for each message sent.
>If I just could use dvb-20030119.tar.bz2 but with auto tuning feature like newer driver.....?
>
>TIA.
>
>B'Regards,
>KOKO
>
>NB: I use Slackware 8
>Linux dvb 2.4.18 #1 Mon Jan 20 02:04:33 WIT 2003 i586 unknown
>
>
>dvb-20030529 detail:
>- make insmod  - ok
>dmesg:
>Linux video capture interface: v1.00
>DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI PCI).
>PCI: Found IRQ 10 for device 00:0d.0
>stv0299.c: setup for tuner BSRU6, TDQB-S00x
>DVB: registering frontend 0:0 (STV0299/TSA5059/SL1935 based)...
>
>lsmod:
>Module                  Size  Used by    Tainted: P
>dvb-ttpci             297108   0  (unused)
>input                   3072   0  [dvb-ttpci]
>ves1820                 3780   0
>stv0299                 6488   0  (unused)
>grundig_29504-491       3188   0
>grundig_29504-401       3528   0
>alps_tdlb7              3724   0
>alps_tdmb7              3276   0
>alps_bsrv2              3444   0
>dvb-core               35044   3  [dvb-ttpci ves1820 stv0299 grundig_29504-491 grundig_29504-401 alps_tdlb7 alps_tdmb7 alps_bsrv2]
>videodev                4448   0  [dvb-ttpci]
>
>- dvbtune (-n dpid     Add network interface and receive MPE on PID dpid) - ok
>Using DVB card "STV0299/TSA5059/SL1935 based"
>tuning DVB-S to L-Band:1073903768, Pol:H Srate=2540000, 22kHz=on
>polling....
>Getting frontend event
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_CARRIER
>polling....
>Getting frontend event
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
>Bit error rate: 62976
>Signal strength: 65535
>SNR: 49836
>FE_STATUS: FE_HAS_SIGNAL FE_HAS_LOCK FE_HAS_CARRIER FE_HAS_VITERBI FE_HAS_SYNC
>Successfully opened network device, please configure the dvb interface
>
>- ifconfig dvb0_0 hw ether 00:02:80:01:03:ea <private_ip> up - ok
>
>- route add -net 224.0.0.0 netmask 240.0.0.0 dev dvb0_0 - ok
>
>- my_simple_multicast_receiver_program/mcastreceive <multicast_ip> <multicast_port> - ok
>dmesg:
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 2 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 01 02 03
>dvb0_0: filter mac=01 00 5e 00 00 01
>dvb0_0: set_mc_list, 1 entries
>dvb0_0: filter mac=00 02 80 01 03 ea
>dvb0_0: filter mac=01 00 5e 00 00 01 
>
>
>
>
>-- 
>Info:
>To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.



-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.