[linux-dvb] Re: SkyStar 2 (cvs dvb-kernel problem)

[Denis Fedorishenko <nuclearcat@nuclearcat.com>]

Hello Denis,

Tuesday, December 2, 2003, 2:03:24 AM, you wrote:

I look, there is no another insmod.sh :D i was thinking something
similar for 2.6

Also just as note, still when i am loading skystar2 i am getting this
message (write error), but everything work fine. If this need, i can
look at daytime model of card and chip (it is on remote site).

DF> Hello Augusto,

DF> Tuesday, December 2, 2003, 1:47:28 AM, you wrote:

DF> Yes, thanks
DF> It was mistake on insmod.sh

DF> Is patch correct? maybe another insmod.sh need same


AC>> Hi!

AC>> Do you know what version do you have of the Skystar2?

AC>> In any case, you need to load the module mt312.o

AC>> 	Augusto

AC>> *********** REPLY SEPARATOR  ***********

AC>> On 12/2/2003 at 1:31 AM Denis Fedorishenko wrote:

>>>Hello linux-dvb,
>>>
>>>I am tried to use new demux code, but got problem on SkyStar-2 now.
>>>Before 1.0.1 working well, but some packetloss and unstable on network
>>>side.
>>>
>>>./getlinks
>>>make
>>>./insmod.sh load
>>>
>>>Linux video capture interface: v1.00
>>>saa7146: register extension 'dvb'.
>>>saa7146: register extension 'budget dvb'.
>>>saa7146: register extension 'budget_ci dvb'.
>>>saa7146: register extension 'budget dvb /w video in'.
>>>usb.c: registered new driver Technotrend/Hauppauge USB-Nova
>>>PCI: Found IRQ 9 for device 01:0b.0
>>>PCI: Sharing IRQ 9 with 00:1f.4
>>>skystar2.c: FlexCopIIB(rev.195) chip found
>>>DVB: registering new adapter (Technisat SkyStar2 driver).
>>>master_xfer: write error 0 !
>>>message 0: flags=0x0, addr=0x68, buf[0]=0x2, len=2
>>>master_xfer: read error !
>>>message 2: flags=0x0, addr=0x68, buf=0x83, len=2
>>>master_xfer: read error !
>>>message 2: flags=0x0, addr=0x1, buf=0x83, len=65099
>>>
>>>root@patohome:~/DVB/dvb-kernel/build-2.4# lsmod
>>>Module                  Size  Used by    Not tainted
>>>skystar2               19080   0  (unused)
>>>dvb-ttusb-budget       21644   0  (unused)
>>>ttpci-eeprom            1840   0
>>>saa7146_vv             33572   0
>>>saa7146                10900   0  [saa7146_vv]
>>>grundig_29504-491       3712   0
>>>grundig_29504-401       4264   0
>>>tda1004x                9124   0
>>>ves1820                 4832   0
>>>stv0299                 7816   0  (unused)
>>>alps_tdmb7              3972   0
>>>alps_tdlb7              5556   0
>>>ves1x93                 4996   0
>>>dvb-core               38892   0  [skystar2 dvb-ttusb-budget
>>>grundig_29504-491 grundig_29504-401 tda1004x ves1820 stv0299 alps_tdmb7
>>>alps_tdlb7 ves1x93]
>>>video-buf              11376   0  [saa7146_vv]
>>>v4l2-common             2752   0  [saa7146_vv]
>>>v4l1-compat            11556   0  [saa7146_vv]
>>>videodev                5664   0  [saa7146_vv]
>>>input                   3200   0
>>>iptable_filter          1644   0  (autoclean) (unused)
>>>ip_tables              12288   1  [iptable_filter]
>>>uhci                   24496   0  (unused)
>>>usbcore                58400   1  [dvb-ttusb-budget uhci]
>>>8139too                15240   1
>>>mii                     2304   0  [8139too]
>>>crc32                   2880   0  [8139too]
>>>pcmcia_core            40032   0
>>>ide-scsi                9424   0
>>>agpgart                39576   0  (unused)
>>>
>>>If need, i can attach my .config of kernel.
>>>Kernel - vanilla 2.4.22
>>>
>>>01:0b.0 Network controller: Techsan Electronics Co Ltd B2C2 Sky2PC PCI
>>>[SkyStar2] (rev 02)
>>>        Subsystem: Techsan Electronics Co Ltd B2C2 Sky2PC PCI [SkyStar2]
>>>        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
>>>ParErr- Stepping- SERR+ FastB2B-
>>>        Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
>>><TAbort- <MAbort- >SERR- <PERR-
>>>        Latency: 32
>>>        Interrupt: pin A routed to IRQ 9
>>>        Region 0: Memory at ff8f0000 (32-bit, non-prefetchable) [size=64K]
>>>        Region 1: I/O ports at df80 [size=32]
>>>
>>>
>>>-- 
>>>Best regards,
>>> Denis                          mailto:nuclearcat@nuclearcat.com
>>>
>>>
>>>
>>>-- 
>>>Info:
>>>To unsubscribe send a mail to ecartis@linuxtv.org with
>>>"unsubscribe linux-dvb" as subject.











-- 
Best regards,
 Denis                            mailto:nuclearcat@nuclearcat.com



-- 
Info:
To unsubscribe send a mail to ecartis@linuxtv.org with "unsubscribe linux-dvb" as subject.