[vdr] Re: NPTL with vdr-1.3.15 may be causing problems

[post <post@mhr.at>]

At 09:25 04.11.2004, you wrote:

> > I'm new to VDR, just did my first installation with a Hauppauge Nexus-S + 
> > SkyStar2 on a Gentoo system with kernel 2.6.8.1 and NPTL enabled. I used 
> > the ebuild from gentoo-de, which installed vdr-1.3.14-r3. When I start 
> > VDR everything seems to be working, I can zap channels, operate in the 
> > menu, but when I try to pause a live-recording, it always does an 
> > emergency exit initated by "ERROR: video data stream broken". Here is my 
> > log, maybe it has something to do with NPTL, or otherwise someone 
> > hopefully can tell me what's the problem:
> What version drivers are you using?
I am using the actual dvb-kernel from CVS, just did the update yesterday, 
before the VDR installation, because the drivers that came with 2.6.8.1 
were pretty old (found a complaint in the dmesg output, that the driver is 
to old and does not support some feedback for sysfs or something like 
that). There was no problem when compiling the kernel, this is the dmesg 
output:

----- cut -----

saa7146: register extension 'dvb'.
ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 19 (level, high) -> IRQ 209
saa7146: found saa7146 @ mem f92ec000 (revision 1, irq 209) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge WinTV Nexus-S rev2.X).
adapter has MAC addr = 00:d0:5c:23:6c:82
dvb-ttpci: gpioirq unknown type=0 len=0
dvb-ttpci: info @ card 0: firm f0240009, rtsl b0250018, vid 71010068, app 
8000261c
dvb-ttpci: firmware @ card 0 supports CI link layer interface
dvb-ttpci: Crystal audio DAC @ card 0 detected
saa7146_vv: saa7146 (0): registered device video0 [v4l2]
DVB: registering frontend 0 (ST STV0299 DVB-S)...
dvb-ttpci: found av7110-0.
ACPI: PCI interrupt 0000:01:09.0[A] -> GSI 17 (level, high) -> IRQ 217
drivers/media/dvb/b2c2/skystar2.c: FlexCopII(rev.130) chip found
drivers/media/dvb/b2c2/skystar2.c: the chip has 6 hardware filters
DVB: registering new adapter (SkyStar2).
DVB: registering frontend 1 (ST STV0299 DVB-S)...
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:01:0a.0[A] -> GSI 16 (level, high) -> IRQ 201
bttv0: Bt878 (rev 2) at 0000:01:0a.0, irq: 201, latency: 32, mmio: 0xd8000000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=61324, tuner=Philips FI1216 MK2 (5), radio=no
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp34xx: init: chip=MSP3410D-B4 +nicam +simple
msp3410: daemon started
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: 
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 
(PV951),ta8874z
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0 [sw]
bttv0: registered device video1
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
i2c_adapter i2c-3: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x5500
flexcop_i2c_func

----- cut -----

I have an old analog Hauppauge WinTV in that machine as well, which I want 
to use to fetch a signal from an old security camera, but I haven't 
installed the analog-plugin yet (but this should not have anything to do 
with that problem).

--
Sincerely,
Master One